Lantronix 900-332 manual Advanced Settings, Configure or modify the following fields for each pin

Page 40

Configuration Using Web-Manager

Encryption Key

Field is enabled when WEP is selected as the Security type. Enter the Encryption Key in hexadecimal value

Advanced Settings

Data Rate	WiPort permits the control of the transmission rate. Select the
	data rate (in Mbps) from the pull down menu.

Radio Power	Power management reduces the overall power consumption
Management	of the WiPort unit. Selecting Enable increases the response
	time.

OEM Pin Configuration

There are 11 configurable hardware pins on the WiPort unit. For each pin, configure the pin function, communication direction, and its activity level. For more information, see Configurable Pins on page 6-1.

To configure the WiPort’s OEM Configurable Pins:

1.Click Configurable Pins from the main menu to open the Configurable Pins window.

Figure 4-11. Configurable Pins Settings

2. Configure or modify the following fields for each pin:

Function	From the pull down menu, select the purpose of the specified
	pin.

Active Level	Select the signal active level (Low or High).

Direction	Select whether the pin inputs or outputs.

4-16	WiPort™ User Guide

Image 40

Contents WiPort User Guide Page Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents Contents Accessing Setup ModeWlan Settings5-19 Expert Settings5-20Factory Defaults Exit Configuration ModeGpio Pins Control ProtocolPage Using This Guide Purpose and AudienceChapter Summary Remaining chapters in this guide includeUsing This Guide Additional DocumentationIntroduction CapabilitiesConfiguration Methods ApplicationsProtocol Support IntroductionAddresses and Port Numbers Hardware AddressIP Address Port NumbersPage Accessing WiPort using DeviceInstaller Configuration using DeviceInstallerServer Configuration Wlan Configuration OEM Pin Configuration Host List ConfigurationConfiguration Using DeviceInstaller Channel 1 and Channel 2 Configuration Common I/F Mode Setting Serial SettingsUDP Datagram Mode Passive ConnectionActive Connection Connection DisconnectionBuffer Flushing Email Configuration PackingTriggers Unit NamePage Configuration using Web-Manager Accessing WiPort using Web-ManagerNetwork Configuration Configuration Using Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationClick the OK button when finished Select Obtain IP address automaticallySelect Use the following IP configuration Default GatewayIP Address Subnet MaskServer Configuration AdvancedRetry Settings Serial SettingsHost Information Port Settings Disable Serial PortAvailable fields, enter the following information ChannelConnection Settings TCP Pack ControlFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Mode Active Connection Connect Mode Passive ConnectionConnect Protocol Disconnect Mode Endpoint ConfigurationCommon Options Connection Settings UDP Datagram ModeChange Address Table Configure the following fieldsMail Server IP Address Configurable Pins Enable Serial TriggerRecipients ConditionsMessage Properties Wireless Network Security Ad Hoc SettingsEnter or modify the following fields Advanced Settings Configure or modify the following fields for each pinUpdating Settings Page Accessing Setup Mode Configuration via Serial Mode or Telnet PortTelnet Access Configuration Via Serial Mode or Telnet Port Serial Port AccessClick OK. The following information displays Set the IP Address Set the Gateway IP AddressChange Telnet Configuration Password Set the NetmaskDhcp Name Network Class Host Bits NetmaskInterface Mode Following table displays available I/F Mode optionsMode Option Interface Mode OptionsCommon I/F Mode Setting Binary Hex FlowPort Number Flow Control OptionConnect Mode Enter Connect Mode options in hexadecimal notationConnect Mode Option Port Numbers Reserved forIncoming Connection ResponseManual Connection Address Example Manual ConnectionAutostart Automatic Connection Hostlist Hostlist ExampleDatagram Type Modem ModeMessage Meaning Modem Mode Commands Modem Mode CommandFunction Remote IP Address Modem Mode Function CommandRemote Port Flush Mode Disconnect Mode Option10. Disconnect Mode Options 11. Flush Mode OptionsOption DisConnTime Inactivity Timeout Channel Port PasswordSendChar 1 and SendChar2 Telnet Terminal TypeMail Server Unit Name Domain NameRecipient TriggerWlan Settings Enable WlanEnable Ad Hoc Network Creation Find Network NameExpert Settings Security SettingsDisable Snmp Disable Telnet SetupDisable Tftp Firmware Upgrade Disable Port 77FE HexFactory Defaults Channel 2 Configuration Channel 1 ConfigurationWlan Settings Exit Configuration Mode Expert SettingsSecurity Settings Email SettingsConfigurable Pins Gpio PinsFeatures Control ProtocolCommands Configurable PinsByte 0 Command Types Command 10h, Get FunctionsCommand 11h, Get Directions Command 12h, Get Active LevelsCommand 13h, Get Current States Command 19h, Set DirectionsCommand 1Ah, Set Active Levels Command 1Bh, Set StatesCommand details Examples1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Monitor Mode Entering Monitor Mode via the Serial PortEntering Monitor Mode via the Network Port To enter Monitor Mode locallyMonitor Mode Commands Following commands are available in Monitor ModeCommand Command Name Function Monitoring the NetworkUsing Tftp Graphical User Interface Updating FirmwareObtaining Firmware Reloading Firmware ROM File FWX FileRecovering the Firmware Using the Serial Port Using Tftp Command Line InterfaceTroubleshooting Problems and Error Messages TroubleshootingProblem/Message Reason Solution Please try again Caps Lock is not onGeneral DeviceInstaller Settings Device Server messageTechnical Support Technical Support Europe, Middle East, and Africa