GarrettCom Magnum 3000 manual Community Community # Name S Manager

Page 49

Magnum 3000 Stackable HubsInstallation and User Guide (07/06)

3. COMMUNITY

C[OMMUNITY] [# [NAME [S] [MANAGER....]]]

Used to set the community string for GET and SET operations.

#--number of community. (Up to 10 different communities may be set)

S --allow SET operations. (If you do not "S" this command, this community will allow only GET operations)

MANAGER --the network manager IP addresses list, up to 10. (If the manager IP addresses list is not present in a command line, any network manager can communicate with this agent using this community string)

Example of two managers: >C 3 MAGNUM S 45.9.0.122 45.9.1.3{Cr}

To display community, type: C{Cr}

To delete community, type: C [#] {Cr}

3. DISPLAY

To display the whole configuration file, type: D{Cr}

Example: >D{Cr} ( All configuration information will appear )

4. EXIT

To exit from the configuration menu, type E{Cr}

Example: >E{Cr}

5. GATEWAY

G[ATEWAY] [# [IP [SUBNETIP [MASKIP]]]]{Cr}

Used to set the gateway IP address and mask. Up to 10 gateways may be set.

Example: >G 3 45.9.0.112 255.255.255.0 255.0.0.0{Cr}

6. MANAGER

M[ANAGER] [# [IP/NAME [PORT] COMMUNITY]]]

Used to set the number of network manager IP addresses, and the community to which TRAPS should be sent. Up to 10 managers may be set. If "PORT" is absent, then TRAPS are sent to port 162, as specified in RFC 1157. If "COMMUNITY" is absent, the community string "public" is used by default.

Example: M 2 45.9.1.125 Magnum{Cr}

7.SUBNETMASK S[UBNETMASK] [IP]{Cr}

To set IP mask, type: S [ mask value] {Cr}

Example: >S 255.255.255.0 {Cr}

NOTE: After entering information using the commands above, to make the new configuration

operative, exit from the configuration menu by typing: E {Cr}. If the agent's IP address has been changed, reset the agent (via a unit power down) to install the change.

www . GarrettCom . com

42

Image 49
Contents Magnum Stackable Hubs Trademarks Magnum Stackable Hubs Installation and User GuideContacting GarrettCom, Inc GarrettCom, IncRevisions PrefaceTable of Contents Specifications Magnum 3024, MagnumIntro Simple Ntwrk Mgmt Protocol Snmp AGENTS32 Magnum Line Specifications Magnum 3024, Magnum LED Indicators on Chassis Front DC Power Supply OptionsWarranty PackagingSpecifications Bridge Port Modules BPMs Bonus Ports Specifications Repeater Port Modules RPMs Bonus PortsOrdering Information Etsi and NEBS-certified models, -48VDC poweredMagnum 3000 Stackable Hubs and Concentrators Network Management OptionsInspecting the Package and Product Introduction Magnum 3012 and 3024 Stackable HubsProduct Description Magnum 3000 Stackable Hubs Stacking Magnum 3000s Magnum 3024 Hub 24 RJ-45 Ports, One PM bonus port slotWww . GarrettCom . com Cable Stack3 4 5 6 7 4a, Magnum 3012 Hub, Front View Magnum 3012 Hub 12 RJ-45 Ports, One PM bonus port slotRear Bonus Slot, Port Modules PMs 5c Magnum 3012 internal layout with configured Bonus Port Included only when PM is factory installedBonus port for optional PM card BPM shown PM Ribbon cable with 16 pin connectorCBL-AUI Features and Benefits, Magnum 3024 and 3012 Hubs Wing B Wing a ApplicationsConnecting Ethernet Media Installation and OperationConnecting Twisted Pair RJ-45, Unshielded or Shielded Connecting ThinNet 10BASE2 BNC Connecting ThickNet 10BASE5 AUIConnecting Drop Cable 10BASE5 DTE Connecting Single-Mode Fiber Optic SMF Connecting Fiber Optic SC-type, Snap-OnAt regular intervals you must use the color-coded strand on Associated ports at each end of the fiber optic segment’cvr Rack-mountingOptional Product Description, Port Modules Introduction Magnum Port ModulesRPM-BNC, RPM-AUI, RPM-DTE RPM-FST or FSC, RPM-SMF, RPM-TP BPM-BNC BPM-AUI BPM-TP BPM-FSTRPM-AUI RPM-BNCDirectly Magnum RPM-BNC Www . GarrettCom . com 2 AUI Pin Assignments RPM-DTEPin Function Magnum RPM-DTEMagnum RPM-FST RPM-FST Fiber ST, Twist-lock ConnectorJumper Across 3 kmRPM-SMF Single-mode Fiber RPM-FSC Fiber SC, Snap-in ConnectorMagnum RPM-FSC Magnum RPM-SMFJumper Across Distances Supported RPM-TP Twisted PairNot used 10 KmMagnum BPM-BNC BPM-BNCBPM-FST BPM-AUIMagnum BPM-FST BPM-TP Ft., or shielded twisted pair wiringEnvironments with maximum Segment distances up to 100mSnmp Agents Description Introduction Simple Network Management Protocol Snmp AgentsEmbedded Snmp Agent, Model 3000-MB Standard Repeater MIB and Extensions Separate Agent Box, Model 3000-AGTWww . GarrettCom . com 3 Magnum Snmp Agent Commands Variable Type Installing the Embedded Agent Board, MB Installation, General Information3b Magnum 3024, Top View with Cover Off Remove Chassis Cover of the hubSet Group # Stack Address Magnum 3024/3012 Magnum Snmp Agent BoardAgent Configuration, Embedded Agent and Agent Box Versions Address\switchEight-Position DIP Switch Configuration Table Switch # 7 and Switch # 8 are not usedManual IP Address Configuration Automatic Agent IP Address ConfigurationPerforming Self Diagnostics Bootp Bootp IP/NAME Bootp IP/NAMEAddress IP/ Name Community # Names ManagerManager Manager # IP/NAME Port Community Community Community # Name S Manager11/12/93 1145 Cr Other Convenience CommandsBefore Calling for Assistance Return Material Authorization RMA Procedure When Calling for AssistanceNo Problem Found Shipping and Packaging Information Appendix a Warranty InformationB1.0 Specifications for Magnum 3000S Appendix B Internal DC Power Supply OptionPower Supply Internal -48VDC Option B3.0 Applications for DC Powered HubsB4.0 InstallationThis section describes Troubleshooting Appendix C Internal DC Dual-Source Power OptionC1.0 Specifications for Magnum 3000S Hubs B5.0 OperationC3.0 DUAL-SOURCE OPTION, Theory of Operation C4.0 Features and Benefits of the DUAL-SOURCE DesignC5.1 UL Requirements C5.0 InstallationExample Magnum 3012-48VDC C6.0 Ordering InformationExample Magnum 3024-24VDC or Magnum 3012-125VDC C7.0 Operation