GE Series 90-70 manual Index

Page 40

Index

A

Active Link fault, 33

Address Assignment, 29

Application software, 3 , 23

B

Board OK bit, 32

C

Cable diagrams, 19 , 20 Cable lengths, 7 Cables and connectors, 6 Calling the Program Block, 24

Catalog Number

Grounding Cable, 19

Optical Adapter, 6

Chassis ground, 19 Communications window time, 24 Configuration error, 34 Configuration example, 28 Configuration, invalid, 33 Configuration, Series 90 PLC, 21 Connectors, 4

Constant Sweep Time CPU mode, 24 Control bit definitions, 30

Control the link, 3 Control word, 26 , 30 Controlling the I/O Link Module, 30 CPU module, 15

CPUs, compatible, 23

Current requirement, 5

D

Data length, 3

Data lengths, 26 , 29

Data transmission rate, 5

Device numbers, 26

Diagnostics, 13

Dimensions, 5

Disable I/O update bits, 30 Distance between devices, 7 DoI/O, 24

E

Electromagnetic noise, 8

Error code bits, 32

Error code definitions, 34 , 35 Example logic, 25 , 28

F

Fanuc I/O Link, 1

Fault Active bit, 32

Faults on I/O Link, 12

G

Getting started, 14

Global (%G) references used, 27 Grounding cable, 19

H

Hardware fault error, 34 Hotline phone number, 34 Humidity specification, 5

I

I/Ocapacity, 1

I/O Link Modules, number of, 3 I/O Links, number of, 23

I/O update, enable/disable bits, 30 Input data, 9 , 10

Inputs, enable/disable, bit, 30 , 31 Installation, 15

36

GFK-0644A

Image 40

Contents GE Fanuc Automation GFL±002 Related Publications Content of this ManualWe Welcome Your Comments and Suggestions Contents Chapter Introduction System OverviewMaster or Slave Operation Application Software Module Description LEDsReset Pushbutton Module SpecificationsSerial Ports Cable Types for the I/O Link CatalogNumberCable Lengths on the I/O Link Optical Adapter Operation of the I/O Link Input and Output DataData Sent by the Master Data Returned by SlavesInputs and Outputs Hold Last State Faults on the I/O Link Diagnostics Link ControlGetting Started Install the module and complete the I/O LinkComplete the program logic for the I/O Link Module Chapter Installation Installing the I/O Link Interface Module in the RackRemoving the I/O Link Interface Module from the Rack LED Name LED Status IndicationPorts on the I/O Link Module Connecting the I/O Link Interface Module to Other DevicesLink Module Used as a Master Link Module Used as a Slave Serial Port Pin AssignmentsOrder of the Devices on the Link Cable Diagram, No Optical Adapter Cable Diagram, Electrical Cable to Optical Adapter Optical Adapter InstallationCable Connections Chapter Logicmaster 90-70 Configuration Configuration StepsGFK-0644A Chapter Programming Guide OverviewSelecting a Program Block Adding the Program Block Logic to an Application ProgramCalling the Program Block Using Multiple Calls to the Program BlockExample Call Instruction Program %P References for the I/O Link Program Blocks 3rdModule 4thModuleUsing Nicknames for the %P References Global %G References for the I/O Link Program BlocksConfiguring I/O Links Configuration Logic, ExampleConfiguration Guidelines Specify the Number of I/O Link ModulesSet Master or Slave Mode bit Reset or Stop bitControlling the I/O Link Module Start/Restart bitDisable or Enable the Input Update bit Disable or Enable the Output Update bitMonitor the Module bit Monitoring Link OperationMonitor Communications Status bit Monitor for an Invalid Configuration or Link Fault bit Monitor for Link Failure bitError Codes Troubleshooting Error Description RecommendedAction CodeConfiguration Error Codes Index GFK-0644A Index