GE Series 90-70 manual GFK-0644A

Page 41

Index

Installation, I/O Link Module, 15

Installation, Optical Adapter, 20

Interrupts, 21

L

LEDs, 4 , 15

Link Active bit, 24 , 32 Link Active LED, 4 , 15 Link Cfg LED, 15 Link control, 13 Link Failed bit, 32 Link failure error, 34 Link operation stops, 12 LINK73X, links and I/O, 23 LINK77X, links and I/O, 23 LINK78X, links and I/O, 23 Logic examples, 25 , 28 Logicmaster 90±70, 21 Logicmaster 90±70 librarian, 24

M

Master devices, 1

Master/slave mode bit, 30

Module appearance, 4

Module installation, 15

Module OK LED, 4 , 15

Module removal, 16

Module type, 5

Monitoring the link, 32

Monitoring the module, 32

Multiple calls, 24

N

Nicknames for %P references, 24 , 26 Normal operation, 34

Number of I/O Link Modules, 1 Number of modules, 29

O

Optical Adapter, 8 , 20 Output data, 9 , 10 Output, +5 volt, 18 , 20 Outputs, enable/disable bit, 30

P

Permissive logic, 30

Pin assignments, 18

Ports, 4

Program Block installation, 24 Program Blocks, 3 , 23 Program nicknames, 26 Program references, 26 Programming, 23

R

Rack location, 3 , 4 , 21 , 26 , 29 Reference addresses, 3 Reference assignment, 29 References, 9

References, maximum, 23 Removal, 16

Reset pushbutton, 4

Reset/Stop link bit, 30

S

Serial port pin assignments, 18 Signal levels, 9

Slave devices, 1

Slot location, 3 , 4 , 26 , 29 Specifications, 5

Start Link bit, 30 Status bit definition, 32 Status word, 26 , 32 Stop Link bit, 30 System overview, 1

GFK-0644A	37

Image 41

Contents GE Fanuc Automation GFL±002 We Welcome Your Comments and Suggestions Content of this ManualRelated Publications Contents System Overview Chapter IntroductionMaster or Slave Operation Application Software LEDs Module DescriptionSerial Ports Module SpecificationsReset Pushbutton CatalogNumber Cable Types for the I/O LinkCable Lengths on the I/O Link Optical Adapter Input and Output Data Operation of the I/O LinkData Returned by Slaves Data Sent by the MasterInputs and Outputs Hold Last State Faults on the I/O Link Link Control DiagnosticsComplete the program logic for the I/O Link Module Install the module and complete the I/O LinkGetting Started Installing the I/O Link Interface Module in the Rack Chapter InstallationLED Name LED Status Indication Removing the I/O Link Interface Module from the RackLink Module Used as a Master Connecting the I/O Link Interface Module to Other DevicesPorts on the I/O Link Module Order of the Devices on the Link Serial Port Pin AssignmentsLink Module Used as a Slave Cable Diagram, No Optical Adapter Cable Connections Optical Adapter InstallationCable Diagram, Electrical Cable to Optical Adapter Configuration Steps Chapter Logicmaster 90-70 ConfigurationGFK-0644A Overview Chapter Programming GuideAdding the Program Block Logic to an Application Program Selecting a Program BlockExample Call Instruction Using Multiple Calls to the Program BlockCalling the Program Block 3rdModule 4thModule Program %P References for the I/O Link Program BlocksGlobal %G References for the I/O Link Program Blocks Using Nicknames for the %P ReferencesConfiguration Logic, Example Configuring I/O LinksSpecify the Number of I/O Link Modules Configuration GuidelinesReset or Stop bit Set Master or Slave Mode bitControlling the I/O Link Module Start/Restart bitDisable or Enable the Output Update bit Disable or Enable the Input Update bitMonitor Communications Status bit Monitoring Link OperationMonitor the Module bit Monitor for Link Failure bit Monitor for an Invalid Configuration or Link Fault bitError Description RecommendedAction Code Error Codes TroubleshootingConfiguration Error Codes Index GFK-0644A Index