Enterasys Networks 6H352-25 manual Installing the Module Into the SmartSwitch Chassis

Page 31

Installing the Module into the SmartSwitch Chassis

5.Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact Enterasys Networks. Refer to Getting Help, in About This Guide.

CAUTION: To prevent damaging the backplane connectors in the following step, take care that the module slides in straight and properly engages the backplane connectors.

Ensure that the top plastic locking tab lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-1.

6.Locate the slot guides that line up with the number of the slot in which the module will be installed. Install the module in the chassis by aligning the module circuit card between the upper and lower metal rail guides of the desired slot, sliding it into the chassis, and locking down the top and bottom plastic locking tabs, as shown in Figure 3-1. Take care that the module slides in straight and properly engages the backplane connectors.

7.If the chassis in which the module is installed was powered down for the installation, turn it back on. Check to see that the CPU LED settles at solid green after a few minutes. If the LED does not turn solid green, see Chapter 4 for details.

3.4INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS

CAUTION: Failure to observe static safety precautions could cause damage to the 6H352-25. Follow static safety handling rules and wear the antistatic wrist strap provided with the SmartSwitch 6000 chassis.

Do not cut the non-conductive bag to remove the module. Sharp objects contacting the board or components can cause damage.

Certain restrictions apply when installing the 6H352-25 into the SmartSwitch 6000 chassis. Refer to the Release Notes for any updated information concerning installing the modules into the SmartSwitch 6000 chassis. Otherwise, the installation procedure from Section 3.4 can be followed, with the exception that the 6C105 chassis has only 5 slots as opposed to the 7 slots in the MATRIX E7. The 6H352-25 can be installed in any of the slots that are available. To install a module, refer to Figure 3-2and proceed as in Section 3.3.

NOTE: The Distributed Chassis Management and SecureFast Switching functionality is supported when the modules are installed in a SmartSwitch 6000 chassis. Refer to the module release notes for specific information on supported functionality.

Installation 3-5

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 6H352-25 Fast Ethernet Installation Guide Page Page Industry Canada Notice FCC NoticeVcci Notice Enterasys NETWORKS, INC Program License Agreement Page Declaration of Conformity Page Contents Network Requirements Figures Tables About This Guide Using this GuideRelated Documents Structure of this GuideGuide uses the following conventions Document ConventionsGetting Help Introduction 6H352-25 Module Optional HSIMs and VHSIMs ConnectivityRuntime IP Address Discovery SmartTrunk HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATIONRemote Monitoring Rmon PORT/VLAN Redirect Functions Broadcast SuppressionTraffic Rate Limiting Flow Control Garp Switch Operation12 802.1 Port Priority Distributed Chassis Management Switching OptionsManagement Standards Compatibility Lanview Diagnostic LEDsNetwork Requirements SmartTrunk Feature10BASE-T Network 100BASE-TX Network Installation Unpacking the 6H352-25 Installing Optional HSIM, VHSIM, or Flash Memory UpgradeInstalling the Module Into the Matrix E7 Chassis Installing the 6H352-25 into the Matrix E7 Chassis Installing the Module Into the SmartSwitch Chassis Installing the 6H352-25 into the SmartSwitch 6000 Chassis Connecting to the Network RX LED TX LED Crossover Cable RJ45 Pinouts Completing the Installation Using Lanview TroubleshootingGroup Select No link Is enabled and there is a OFF Troubleshooting ChecklistRefer to Matrix E7 Series Reset Button Using the Reset Button8Troubleshooting Ports SpecificationsEnvironmental COM Port Pinout AssignmentsRegulatory Compliance Page Required Tools Mode Switch Bank Settings and OptionsFigure B-1 Mode Switch Location Setting the Mode SwitchesSetting the Mode Switches Locating the Flash Memory Flash Memory UpgradeInstalling the Flash Memory Figure B-4 Hsim and Vhsim Connector Locations Installing Optional Hsim or Vhsim Interface ModulesNumerics IndexIndex-2
Top Page Image Contents