Enterasys Networks C2K122-24 About This Guide, Who Should Use This Guide, How to Use This Guide

Page 17

About This Guide

This guide provides an overview, installation and troubleshooting instructions, and specifications for the Enterasys® SecureStack C2K122‐24 stackable Gigabit switch with 10‐Gigabit Ethernet uplinks.

For information about the Command Line Interface (CLI) set of commands used to configure and manage the switch, refer to the Enterasys Networks® SecureStack C2 Configuration Guide.

Note: In this guide, the following terms are used:

• Switch refers to a C2K122-24, unless otherwise noted.

•XSP refers to optional small-form pluggable interface modules that plug into the front panel port slots 25 and 26.

Important Notice

Depending on the firmware version used in the C2K122-24 switch, some features described in this document may not be supported. Refer to the Release Notes shipped with the switch to determine which features are supported.

Who Should Use This Guide

This guide is intended for a network administrator responsible for installing and setting up the stackable switch.

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

How to Use This Guide

Read through this guide completely to familiarize yourself with its contents to gain an understanding of the features and capabilities of the stackable switch. A general knowledge of data communications networks is helpful when setting up the switch.

SecureStack C2 Installation Guide xv

Image 17

Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide How to Use This GuideAbout This Guide For Refer to Related DocumentsFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Overview IntroductionC2K122-24 C2K122-24 Stackable Switch FrontConnectivity Redundant Power Supply CapabilityHigh-Speed Stack Connections Description of XFPsSwitch Configuration Using WebView Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands ManagementSupport@enterasys.com Getting HelpGetting Help Introduction 10BASE-TX Network Network Requirements10GBASE-XX Network 100BASE-TX Network1000BASE-T Network Type Max. Length Connector Recommended Cable Types and Specifications10GBASE-XX Network Network Requirements Hardware Installation Unpacking the Switch Considerations Prior to InstallationContents of Switch Carton Quantity Required ToolsPreparation Installing Optional XFPsRemoving the XFP Installing the XFPInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for InstallationArea Guidelines for Switch Installation on Flat Surface Rack Mounting the SwitchAttaching Brackets and Installing in Rack Guidelines for Rackmount InstallationFastening the Switch to the Rack Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections Configuring Switches in a StackAbout SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS PowerSwitch Rear View Stack Initialization Overview RPS PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2K122-24 Lanview LEDs Using LanviewColor State Recommended Action Lanview LEDsRPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Table A-1 Switch Specifications C2K122-24 Switch SpecificationsPhysical EnvironmentalTable A-2 Supported XFP Transceivers SpecificationSupported XFP Transceiver Interface Options Table A-5 Compliance Standards Regulatory Compliance Console Port Pinout AssignmentsRegulatory Compliance Numerics IndexInstallation of 3-3specifications for A-3