Enterasys Networks C2K122-24 manual Installing the XFP, Removing the XFP

Page 34

Installing Optional XFPs

Installing the XFP

To install an XFP that has an LC connector, refer to Figure 3‐1, and proceed as follows:

1.Hold the XFP with the top side positioned as shown, and the edge connector facing the port slot.

2.Align the XFP with the port slot.

3.Push the XFP into the port slot until the XFP “clicks” and locks into place.

Figure 3-1 XFP with LC Connector

Å

Ä

TX

RX

25

26

C2K122-24

Á Ã

Â

À

1XFP

2XFP, top side

3Edge connector (insertion side)

4Port slot

5Protective dust cover

6Wire handle (for XFP release)

Removing the XFP

Caution: Do NOT remove the XFP from the port slot without releasing it. The XFP is released by pulling down on its wire handle. Attempting to remove the XFP without releasing it can damage the XFP.

The XFP and its host switch are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damaging the XFP or host switch. Always leave the XFP in the antistatic bag or an equivalent antistatic container when not installed.

Precaución: NO quite el XFP de la ranura sin antes abrir la traba ubicada en la parte frontal del XFP. Si lo hace, puede dañar el XFP, puesto que es muy sensible a las descargas de electricidad estática, al igual que el dispositivo host. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, pude dañar el XFP o el dispositivo host. Mientras no esté instalado, mantenga el XFP en su bolsa antiestática o en cualquier otro recipiente antiestático.

3-4 Hardware Installation

Image 34
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide How to Use This GuideWho Should Use This Guide Related Documents For Refer toConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction OverviewC2K122-24 Stackable Switch Front C2K122-24High-Speed Stack Connections Redundant Power Supply CapabilityConnectivity Description of XFPsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsSwitch Configuration Using WebView ManagementGetting Help Support@enterasys.comGetting Help Introduction Network Requirements 10BASE-TX Network1000BASE-T Network 100BASE-TX Network10GBASE-XX Network Recommended Cable Types and Specifications Type Max. Length Connector10GBASE-XX Network Network Requirements Hardware Installation Contents of Switch Carton Quantity Considerations Prior to InstallationUnpacking the Switch Required ToolsInstalling Optional XFPs PreparationInstalling the XFP Removing the XFPInstalling the Switch on a Flat Surface Installing the Rubber FeetGuidelines for Installation Chassis Bottom, Rubber Feet PlacementRack Mounting the Switch Area Guidelines for Switch Installation on Flat SurfaceGuidelines for Rackmount Installation Attaching Brackets and Installing in RackConnecting High-Speed Stacking Cables Fastening the Switch to the RackConfiguring Switches in a Stack High-Speed Stacking Cable ConnectionsAbout SecureStack C2 Switch Operation in a Stack Recommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and RPS Power AC PowerSwitch Rear View RPS Power Stack Initialization OverviewConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting a VT Series TerminalConnecting to a Modem 11 Connecting to a ModemConnecting to the Network Connecting UTP Cables13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using Lanview C2K122-24 Lanview LEDsLanview LEDs Color State Recommended ActionRPS Troubleshooting Checklist Refer to the SecureStack C2 Configuration Guide for properRefer to the SecureStack C2 Configuration Guide for the IP Using the Password Reset Switch Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Physical Switch SpecificationsTable A-1 Switch Specifications C2K122-24 EnvironmentalSupported XFP Transceiver Interface Options SpecificationTable A-2 Supported XFP Transceivers Regulatory Compliance Console Port Pinout AssignmentsTable A-5 Compliance Standards Regulatory Compliance Index NumericsInstallation of 3-3specifications for A-3