Enterasys Networks C2K122-24 manual Related Documents, For Refer to

Page 18

Related Documents

This preface provides an overview of this guide and the SecureStack C2 manual set, a brief summary of each chapter and defines the conventions used throughout this guide. To locate information concerning various subjects in this guide, refer to the following table:

For...

Refer to...

 

 

An overview of the switch features and how to

Chapter 1, Introduction

obtain technical support

 

 

 

Network requirements that must be met before

Chapter 2, Network Requirements

installing the switch

 

 

 

Instructions to install the switch on a flat surface

Chapter 3, Hardware Installation

or in a standard 19-inch rack and configure the

 

switch in a stacked configuration

 

 

 

Troubleshooting installation problems and

Chapter 4, Troubleshooting

diagnosing network/operational problems using

 

the LANVIEW LEDs

 

 

 

Specifications, environmental requirements, and

Appendix A, Specifications

physical properties of the switch and optional

 

XFPs

 

 

 

Related Documents

The documents listed below provide the necessary information to install and configure the switch and can be obtained from the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site:

http://www.enterasys.com/support/manuals

SecureStack C2 Installation Guide provides hardware specifications and instructions to install the switch and its options.

SecureStack C2 Configuration Guide describes how to use the Command Line Interface (CLI) to set up and manage the C2 switch.

SecureStack C2 Redundant Power System C2RPS‐SYS Installation Guide provides hardware specifications and instructions to install the power supply and its options.

Cabling Guide provides information on dB loss and cable specifications.

Unlike the other documents listed above, the Cabling Guide is not listed alphabetically on the web site. Instead, it is listed under the Overview Guides link.

xvi About This Guide

Image 18
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv How to Use This Guide About This GuideWho Should Use This Guide Related Documents For Refer toConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction OverviewC2K122-24 Stackable Switch Front C2K122-24High-Speed Stack Connections Redundant Power Supply CapabilityConnectivity Description of XFPsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsSwitch Configuration Using WebView ManagementGetting Help Support@enterasys.comGetting Help Introduction Network Requirements 10BASE-TX Network100BASE-TX Network 1000BASE-T Network10GBASE-XX Network Recommended Cable Types and Specifications Type Max. Length Connector10GBASE-XX Network Network Requirements Hardware Installation Contents of Switch Carton Quantity Considerations Prior to InstallationUnpacking the Switch Required ToolsInstalling Optional XFPs PreparationInstalling the XFP Removing the XFPInstalling the Switch on a Flat Surface Installing the Rubber FeetGuidelines for Installation Chassis Bottom, Rubber Feet PlacementRack Mounting the Switch Area Guidelines for Switch Installation on Flat SurfaceGuidelines for Rackmount Installation Attaching Brackets and Installing in RackConnecting High-Speed Stacking Cables Fastening the Switch to the RackConfiguring Switches in a Stack High-Speed Stacking Cable ConnectionsAbout SecureStack C2 Switch Operation in a Stack Recommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and RPS Power AC PowerSwitch Rear View RPS Power Stack Initialization OverviewConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting a VT Series TerminalConnecting to a Modem 11 Connecting to a ModemConnecting to the Network Connecting UTP Cables13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using Lanview C2K122-24 Lanview LEDsLanview LEDs Color State Recommended ActionRPS Troubleshooting Checklist Refer to the SecureStack C2 Configuration Guide for properRefer to the SecureStack C2 Configuration Guide for the IP Using the Password Reset Switch Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Physical Switch SpecificationsTable A-1 Switch Specifications C2K122-24 EnvironmentalSpecification Supported XFP Transceiver Interface OptionsTable A-2 Supported XFP Transceivers Console Port Pinout Assignments Regulatory ComplianceTable A-5 Compliance Standards Regulatory Compliance Index NumericsInstallation of 3-3specifications for A-3