Enterasys Networks C2K122-24 manual Using the Password Reset Switch

Page 63

Using the Password Reset Switch

Using the Password Reset Switch

If you forget the switch login password, use the Password Reset switch as described in the following procedure.

Figure 4-3 Password Reset Switch

À

1Password Reset switch

To reset the switch password, refer to Figure 4‐3 and proceed as follows:

Note: Notify the system manager before changing the password.

1.Press‐and‐hold the Reset button while the switch is operational. This change of the login password to the default password will be indicated via CLI only.

2.Logon to device management. You can now logon to the switch via the Console port and assign a new password using the command line interface (CLI).

3.To access switch management from your local PC, terminal, or modem connection, refer to the SecureStack C2 Configuration Guide for instructions on how to log in and enter a new password. The guide is available online at:

http://www.enterasys.com/support/manuals

If you require assistance, contact Enterasys Networks using one of the methods described in “Getting Help” on page 1‐5.

SecureStack C2 Installation Guide 4-7

Image 63
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv How to Use This Guide About This GuideWho Should Use This Guide For Refer to Related DocumentsFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Overview IntroductionC2K122-24 C2K122-24 Stackable Switch FrontDescription of XFPs Redundant Power Supply CapabilityConnectivity High-Speed Stack ConnectionsManagement Lanview Diagnostic LEDsSwitch Configuration Using WebView Switch Configuration Using CLI CommandsSupport@enterasys.com Getting HelpGetting Help Introduction 10BASE-TX Network Network Requirements100BASE-TX Network 1000BASE-T Network10GBASE-XX Network Type Max. Length Connector Recommended Cable Types and Specifications10GBASE-XX Network Network Requirements Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton QuantityPreparation Installing Optional XFPsRemoving the XFP Installing the XFPInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for InstallationArea Guidelines for Switch Installation on Flat Surface Rack Mounting the SwitchAttaching Brackets and Installing in Rack Guidelines for Rackmount InstallationFastening the Switch to the Rack Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections Configuring Switches in a StackAbout SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS PowerSwitch Rear View Stack Initialization Overview RPS PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2K122-24 Lanview LEDs Using LanviewColor State Recommended Action Lanview LEDsRPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Environmental Switch SpecificationsTable A-1 Switch Specifications C2K122-24 PhysicalSpecification Supported XFP Transceiver Interface OptionsTable A-2 Supported XFP Transceivers Console Port Pinout Assignments Regulatory ComplianceTable A-5 Compliance Standards Regulatory Compliance Numerics IndexInstallation of 3-3specifications for A-3