Enterasys Networks C2K122-24 manual Getting Help, Support@enterasys.com

Page 25

Getting Help

Getting Help

For additional support related to the switch or this document, contact Enterasys Networks using one of the following methods:

World Wide Web

www.enterasys.com/services/support/

Phone

1-800-872-8440(toll-free in U.S. and Canada)

 

or 1-978-684-1000

 

For the Enterasys Networks Support toll-free number in your country:

 

www.enterasys.com/services/support/contact/

 

 

Internet mail

support@enterasys.com

 

To expedite your message, type [SWITCHING] in the subject line.

To send comments concerning this document to the Technical Publications Department: techpubs@enterasys.com

Please include the document Part Number in your email message.

Before contacting Enterasys Networks for technical support, have the following information ready:

Your Enterasys Networks service contract number

A description of the failure

A description of any action(s) already taken to resolve the problem (for example, changing mode switches, rebooting the unit, etc.)

The serial and revision numbers of all involved Enterasys Networks products in the network

A description of your network environment (layout, cable type, etc.)

Network load and frame size at the time of trouble (if known)

The device history (that is, have you returned the device before, is this a recurring problem, and so forth.)

Any previous Return Material Authorization (RMA) numbers

SecureStack C2 Installation Guide 1-5

Image 25
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide How to Use This GuideWho Should Use This Guide For Refer to Related DocumentsFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Overview IntroductionC2K122-24 C2K122-24 Stackable Switch FrontConnectivity Redundant Power Supply CapabilityHigh-Speed Stack Connections Description of XFPsSwitch Configuration Using WebView Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands ManagementSupport@enterasys.com Getting HelpGetting Help Introduction 10BASE-TX Network Network Requirements1000BASE-T Network 100BASE-TX Network10GBASE-XX Network Type Max. Length Connector Recommended Cable Types and Specifications10GBASE-XX Network Network Requirements Hardware Installation Unpacking the Switch Considerations Prior to InstallationContents of Switch Carton Quantity Required ToolsPreparation Installing Optional XFPsRemoving the XFP Installing the XFPInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for InstallationArea Guidelines for Switch Installation on Flat Surface Rack Mounting the SwitchAttaching Brackets and Installing in Rack Guidelines for Rackmount InstallationFastening the Switch to the Rack Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections Configuring Switches in a StackAbout SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS PowerSwitch Rear View Stack Initialization Overview RPS PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2K122-24 Lanview LEDs Using LanviewColor State Recommended Action Lanview LEDsRPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Table A-1 Switch Specifications C2K122-24 Switch SpecificationsPhysical EnvironmentalSupported XFP Transceiver Interface Options SpecificationTable A-2 Supported XFP Transceivers Regulatory Compliance Console Port Pinout AssignmentsTable A-5 Compliance Standards Regulatory Compliance Numerics IndexInstallation of 3-3specifications for A-3