Enterasys Networks C2K122-24 manual Connecting to an IBM or Compatible Device, Parameter Setting

Page 47

Connecting to Console Port for Local Management

Connecting to an IBM or Compatible Device

To connect an IBM PC or compatible device, running the VT terminal emulation, to an Enterasys switch Console port (Figure 3‐9), proceed as follows:

1.Connect the DB9 female connector at one end of the cable (not supplied) to the Console port on the Enterasys switch. (If there is a switch designated as the Manager, connect to its Console port.)

2.Plug the DB9 female connector at the other end of cable into the communications port on the PC.

3.Turn on the PC and configure your VT emulation package with the following parameters:

Parameter	Setting

Mode	7	Bit Control

Transmit	Transmit=9600

Bits Parity	8	Bits, No Parity

Stop Bit	1	Stop Bit

When these parameters are set, the Startup screen will display. Proceed to “Connecting to the Network” on page 3‐20.

Figure 3-9 Connecting an IBM PC or Compatible

Console

M
	GR
	RPS
CPU	UP
CPU	DO
	WN

1

2

	Ä Ã		Á	À	Â
1	DB9 female connector	4	DB9 female connector
2	Serial interface cable	5	PC with VT emulation application

3DB9 male Console port connector

SecureStack C2 Installation Guide 3-17

Image 47

Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide How to Use This GuideAbout This Guide For Refer to Related DocumentsFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Overview IntroductionC2K122-24 C2K122-24 Stackable Switch FrontDescription of XFPs Redundant Power Supply CapabilityConnectivity High-Speed Stack ConnectionsManagement Lanview Diagnostic LEDsSwitch Configuration Using WebView Switch Configuration Using CLI CommandsSupport@enterasys.com Getting HelpGetting Help Introduction 10BASE-TX Network Network Requirements10GBASE-XX Network 100BASE-TX Network1000BASE-T Network Type Max. Length Connector Recommended Cable Types and Specifications10GBASE-XX Network Network Requirements Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton QuantityPreparation Installing Optional XFPsRemoving the XFP Installing the XFPInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for InstallationArea Guidelines for Switch Installation on Flat Surface Rack Mounting the SwitchAttaching Brackets and Installing in Rack Guidelines for Rackmount InstallationFastening the Switch to the Rack Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections Configuring Switches in a StackAbout SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS PowerSwitch Rear View Stack Initialization Overview RPS PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2K122-24 Lanview LEDs Using LanviewColor State Recommended Action Lanview LEDsRPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Environmental Switch SpecificationsTable A-1 Switch Specifications C2K122-24 PhysicalTable A-2 Supported XFP Transceivers SpecificationSupported XFP Transceiver Interface Options Table A-5 Compliance Standards Regulatory Compliance Console Port Pinout AssignmentsRegulatory Compliance Numerics IndexInstallation of 3-3specifications for A-3