Enterasys Networks C2K122-24 manual Supplement to Product Instructions

Page 6

Supplement to Product Instructions

 



 

 

 

(Hazardous Substance)

 

(Parts)













 

 

3E

+J

&G

&U

3%%

3%'(



(Metal Parts)



(Circuit Modules)



(Cables & Cable Assemblies)



(Plastic and Polymeric parts)



(Circuit Breakers)



SJ/T 11363-2006



Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T 11363-2006 standard.

SJ/T 11363-2006



Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard.









This table shows where these substances may be found in the supply chain of Enterasys’ electronic information products, as of the date of sale of the enclosed product. Note that some of the component types listed above may or may not be a part of the enclosed product.



 

 



 





 

20

 

 

 



 

 

 

 

The Environmentally Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here, unless otherwise marked. Certain parts may have a different EFUP (for example, battery modules) and so are marked to reflect such. The Environmentally Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.

iv

Image 6
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv How to Use This Guide About This GuideWho Should Use This Guide Related Documents For Refer toConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction OverviewC2K122-24 Stackable Switch Front C2K122-24High-Speed Stack Connections Redundant Power Supply CapabilityConnectivity Description of XFPsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsSwitch Configuration Using WebView ManagementGetting Help Support@enterasys.comGetting Help Introduction Network Requirements 10BASE-TX Network100BASE-TX Network 1000BASE-T Network10GBASE-XX Network Recommended Cable Types and Specifications Type Max. Length Connector10GBASE-XX Network Network Requirements Hardware Installation Contents of Switch Carton Quantity Considerations Prior to InstallationUnpacking the Switch Required ToolsInstalling Optional XFPs PreparationInstalling the XFP Removing the XFPInstalling the Switch on a Flat Surface Installing the Rubber FeetGuidelines for Installation Chassis Bottom, Rubber Feet PlacementRack Mounting the Switch Area Guidelines for Switch Installation on Flat SurfaceGuidelines for Rackmount Installation Attaching Brackets and Installing in RackConnecting High-Speed Stacking Cables Fastening the Switch to the RackConfiguring Switches in a Stack High-Speed Stacking Cable ConnectionsAbout SecureStack C2 Switch Operation in a Stack Recommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and RPS Power AC PowerSwitch Rear View RPS Power Stack Initialization OverviewConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting a VT Series TerminalConnecting to a Modem 11 Connecting to a ModemConnecting to the Network Connecting UTP Cables13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using Lanview C2K122-24 Lanview LEDsLanview LEDs Color State Recommended ActionRPS Troubleshooting Checklist Refer to the SecureStack C2 Configuration Guide for properRefer to the SecureStack C2 Configuration Guide for the IP Using the Password Reset Switch Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Physical Switch SpecificationsTable A-1 Switch Specifications C2K122-24 EnvironmentalSpecification Supported XFP Transceiver Interface OptionsTable A-2 Supported XFP Transceivers Console Port Pinout Assignments Regulatory ComplianceTable A-5 Compliance Standards Regulatory Compliance Index NumericsInstallation of 3-3specifications for A-3