Enterasys Networks C2K122-24 manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

2008 Enterasys Networks, Inc. All rights reserved. Part Number: 9034087‐04 February 2008

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, ENTERASYS SECURESTACK, LANVIEW, NETSIGHT, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv How to Use This Guide About This GuideWho Should Use This Guide For Refer to Related DocumentsFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Overview IntroductionC2K122-24 C2K122-24 Stackable Switch FrontDescription of XFPs Redundant Power Supply CapabilityConnectivity High-Speed Stack ConnectionsManagement Lanview Diagnostic LEDsSwitch Configuration Using WebView Switch Configuration Using CLI CommandsSupport@enterasys.com Getting HelpGetting Help Introduction 10BASE-TX Network Network Requirements100BASE-TX Network 1000BASE-T Network10GBASE-XX Network Type Max. Length Connector Recommended Cable Types and Specifications10GBASE-XX Network Network Requirements Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton QuantityPreparation Installing Optional XFPsRemoving the XFP Installing the XFPInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Guidelines for InstallationArea Guidelines for Switch Installation on Flat Surface Rack Mounting the SwitchAttaching Brackets and Installing in Rack Guidelines for Rackmount InstallationFastening the Switch to the Rack Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections Configuring Switches in a StackAbout SecureStack C2 Switch Operation in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAC Power Connecting AC and RPS PowerSwitch Rear View Stack Initialization Overview RPS PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2K122-24 Lanview LEDs Using LanviewColor State Recommended Action Lanview LEDsRPS Refer to the SecureStack C2 Configuration Guide for proper Troubleshooting ChecklistRefer to the SecureStack C2 Configuration Guide for the IP Password Reset Switch Using the Password Reset SwitchUsing the Password Reset Switch Troubleshooting Specifications Environmental Switch SpecificationsTable A-1 Switch Specifications C2K122-24 PhysicalSpecification Supported XFP Transceiver Interface OptionsTable A-2 Supported XFP Transceivers Console Port Pinout Assignments Regulatory ComplianceTable A-5 Compliance Standards Regulatory Compliance Numerics IndexInstallation of 3-3specifications for A-3