Enterasys Networks C2H124-48P, C2G124-48P manual Electromagnetic Compatibility EMC

Page 5

ELECTROMAGNETIC COMPATIBILITY (EMC)

This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3.

COMPATIBILIDAD ELECTROMÁGNETICA (EMC)

Este producto de Enterasys cumple con lo siguiente: 47 CFR Partes 2 y 15, CSA C108.8, 89/336/EEC, EN 55022, EN 55024, EN 61000‐3‐2, EN 61000‐3‐3, AS/NZS CISPR 22, VCCI V‐3.

ELEKTRO- MAGNETISCHE KOMPATIBILITÄT ( EMC )

Dieses Produkt entspricht den folgenden Richtlinien: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3.

HAZARDOUS SUBSTANCES

This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment.

EUROPEAN WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) NOTICE

In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE):

1.The symbol above indicates that separate collection of electrical and electronic equipment is required and that this product was placed on the European market after August 13, 2005, the date of enforcement for Directive 2002/96/EC.

2.When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately.

3.It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.

4.It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated.

For information about the available collection system, please go to http://www.enterasys.com/services/support/ or contact Enterasys Customer Support at 353 61 705586 (Ireland).

iii

Image 5
Contents Enterasys SecureStack C2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide About This GuideRelated Documents How to Use This GuideFollowing conventions are used in this guide Conventions Used in This GuidePage Overview IntroductionC2G124-48P Stackable Switch C2G124-48P Stackable Switch C2H124-48P Stackable SwitchHigh-Speed Stack Connections C2H124-48P Stackable SwitchPowered Device Classifications Usage PD Maximum Power Range PoE Power over Ethernet SupportRedundant Power Supply Capability Connectivity Switch Configuration Using WebViewManagement Description of Mini-GBICsSwitch Configuration Using CLI Commands Lanview Diagnostic LEDsStandards Compatibility Getting HelpGetting Help Network Requirements 1000BASE-FX Network 10BASE-TX Network100BASE-TX Network 1000BASE-T Network 1000BASE-T Network Network Requirements Hardware Installation Unpacking the Switch Considerations Prior to InstallationContents of Switch Carton Quantity Required ToolsPreparing to Install a Mini-GBIC Installing Optional Mini-GBICsMini-GBIC with MT-RJ Connector Mini-GBIC with LC Connector Removing a Mini-GBIC Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Installing the Rubber FeetArea Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationAttaching Brackets and Installing in Rack Rack Mounting the SwitchGuidelines for Rackmount Installation Attaching the Rackmount Brackets Connecting High-Speed Stacking CablesHigh-Speed Stacking Cable Connections About SecureStack C2 Switch Operation in a Stack Configuring Switches in a StackInstalling a New Stackable System of Up to Eight Switches Recommended Procedures to Install New and Existing StacksImportant Considerations About Using Clear Config in a Stack Switch Rear View Connecting AC and PoE PowerStack Initialization Overview PoE PowerWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal11 Connecting a VT Series Terminal Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Connecting a UTP Cable Segment to RJ45 port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1- TX2+ TX3+ RX3- RX2- TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports C2G124 Connecting Fiber-Optic Cables to LC Ports Connecting to the Network 19 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting C2G124-48P Lanview LEDs Using LanviewC2H124-48P Lanview LEDs Color State Recommended Action Lanview LED Diagnostic IndicationsRPS Mgbic Refer to the SecureStack C2 Configuration Guide for the IP Troubleshooting ChecklistReset Button Using the Reset ButtonUsing the Reset Button Using the Reset Button Troubleshooting Table A-1 Switch Specifications ItemSpecification C2G124-48P/C2H124-48P Switch SpecificationsProcessors/Memory Table A-1 Switch Specifications C2H124-48PTable A-2 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsMGBIC-LC03 Specifications 1000BASE-LX Gigabit Ethernet SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-9 MGBIC-08 Optical Specifications Table A-11 MGBIC-02 SpecificationsTable A-12 Compliance Standards Regulatory Compliance Console Port Pinout AssignmentsRegulatory Compliance Regulatory Compliance Specifications Index Index-2