Dialogic SS7G21, SS7G22 manual International Warnings

Page 70

Chapter 11 International Warnings

Warning: English (continued)

A microprocessor and heat sink might be hot if the system has been running. Also, there might be sharp pins and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves.

Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.

The system is designed to operate in a typical office environment. Choose a site that is:

Clean and free of airborne particles (other than normal room dust).

Well-ventilated and away from sources of heat including direct sunlight.

Away from sources of vibration or physical shock.

Isolated from strong electromagnetic fields produced by electrical devices.

Protected when in regions that are susceptible to electrical storms. We recommend you plug your system into a surge suppressor and disconnect telecommunication lines to your modem during an electrical storm.

Provided with a properly grounded wall outlet.

Provided with sufficient space to access the power supply cords, because they serve as the product’s mains power disconnect.

Servers can be too heavy for a single person to lift or move safely. Depending on the server, use two people or a mechanical assist to lift or move the server.

70

Image 70
Contents Dialogic SS7G21 and SS7G22 Signaling Servers Publication Date January Document Number 05-2300-007, Issue Contents Figures IndexTables Date Issue No DescriptionRevision History Part 1 User’s Guide Qualified Service Technician Operations If AC Power Supplies are Installed Mains AC Power Disconnect If DC Power Supplies are Installed Isolation Page Purpose IntroductionProducts Server Board Power SuppliesSS7 Signaling Boards Hard Disk DriveCooling Ethernet PortsRelated Information Product Applicability ApplicabilityProduct ID Description AC Power Supply Module Product SpecificationDC Power Supply Module Signaling LinksSS7 Serial Interfaces PCM InterfaceEthernet Interfaces Controls and Indicators Alarm OutputsSerial Port COM2 ID switch MNR Alarm LED amber PWR Alarm LED amberActivity/Fault LED green/amber Visual Indicators on the Ethernet PortsProduct Reliability Physical SpecificationsEnvironmental Specifications Calculated Product ReliabilityProduct Specification Specifications Demonstrating Compliance Safety Compliance Regulatory Specifications and DeclarationsElectromagnetic Compatibility EMC Telecommunications Compliance US ICKCNNANSS7HDPDeclaration of Conformity Declarations of the Manufacturer or ImporterNo D0006 Česky FCC Part 15 ElectroMagnetic Compliance Statement USA FCC Part 68 Statement USATelecommunications Notice Australia / New Zealand Telecommunications Attachment Notice CanadaTelecommunications Notice Taiwan Essential Compliance Information Safety2 EMC Installation of Cables Further InformationProduct Environmental Information Regulatory Specifications and Declarations Hardware Description OverviewFeature Description More Information Front Panel Control, Indicator and Switch Function SummaryFront Panel Back Panel Description InformatioRack Mounting Options AC Power Input DC Power Input Terminal BlockSafety Ground Studs for Earthing InterfacesSS7 Serial Interface Ports PCM Interface Ports Connector PinoutsPin No Direction Function SS7 Serial Interface Connector Aux on SPCI2S SS7 Serial Interface Ports Dual V.11 Connector PinoutsEthernet Interfaces Connectors Ethernet Interface Connector Pinouts Serial Port COM2 ConnectorAlarms Pin No DescriptionPart 2 Service Technician’s Guide Page Qualified Service Technician Operations If AC Power Supplies are Installed Mains AC Power Disconnect If DC Power Supplies are Installed Isolation Page Tools and Supplies Needed Tools and Supplies NeededTools and Supplies Needed Product Installation and Hot-Swap Actions Installation OverviewPower Supply Related Actions Safety Ground Studs, Conductor Installation Replacement of Power Supply Module in AC ProductsDC Power Supply Module, Initial Connections DC Power Supply Module Terminal Block DC Power Supply Module, Transferring Connections AC-input Power Supply Cage, ConnectionProduct Installation and Hot-Swap Actions Unlocking and Removing an AC Power Supply Module Hard Disk Drive HDD ReplacementReplacing the Hardware Backing up the System ConfigurationFiles Backed Up to the syslog Subdirectory at Startup File Type DescriptionRestoring the System Configuration Replacing the Hard Disk DriveProduct Installation and Hot-Swap Actions Safety Before Removing the Top Cover Working Inside the ProductRemoving and Installing the Top Cover Top Cover Removal and Installation Internal Product Layout Major Components in an SS7G21 and SS7G22 Chassis 10.5 SS7 Signaling BoardsPreparing Spci Signaling Boards for Installation in SS7G21 SS7G21 VariantsQuantity of Boards Variant Suffix Board Position Board Boards SwitchD1W D2W Position D3W / Q3W Setting Positions Q1W Q2W JumpersInstalling or Replacing an SS7 Signaling Board Boards Position Switch 00W H1W H2W H3W SettingInstalling and Replacing an SS7 Signaling Board Replacing the Back-up Battery CT Bus Cable NotesVarning Working Inside the Product International Warnings International Warnings Avertissements Français Avertissements Français suite Warnung Deutsch Warnung Deutsch Fortsetzung Avvertenza Italiano Avvertenza Italiano continua Advertencia Español Advertencia Español continuación Product ID Description SS7G21 and SS7G22 Product IDs Operating Mode IDsPart Number Reference Protocol Module IDsAccessories Expansion Options or Spare AssembliesLinux Software Distribution Software Licensing InformationGNU C Library Software Licensing Information Appendix a Connecting to V.11 V.35-Compatible SS7 LinksConnectors on the SPCI2S Signaling Board CablingConnecting an SPCI2S to a Nortel DMS100 Connecting an SPCI2S to an M34 Block ConnectorConnecting an SPCI2S to an Inet Tester SPCI2S/SIU Generates Clocking Configuring the SIU SPCI2S to Operate on V.11 PortsClocking SPCI2S/SIU Receiving ClockAppendix a Glossary CT BusGlossary Index FCCMtbf Switches