DigiTech RP1000 owner manual Getting Started, Making Connections, Amp Loop, Stomp Loop

Page 12

Getting Started

Making Connections

There are lots of ways to connect the RP1000 to amps, effects, mixers, and other equipment. Before connecting the RP1000 to anything, make sure both your amp and the RP1000 are turned off.

Amp/Cabinet Bypass

The RP1000 lets you bypass its amp and cabinet tones so you can apply its effects to your own amp/cabinet tone.To bypass the RP1000 amp and cabinet tones in all presets, push the Amp/ Cabinet Bypass button so it’s lit. To utilize the RP1000 amp and cabinet tones, push the Amp/ Cabinet Bypass button so it’s not lit.

Amp Loop

The RP1000’s Amp Loop lets you use an external amplifier or preamp with the RP1000’s signal path instead of the RP1000’s internal amps and cabinets. You can turn on the Amp Loop with the Amp Loop button on the left side of the matrix. With this button enabled, the external amp or preamp is placed in the signal path around internal amps and cabinets, so the internal amps and cabinets are totally bypassed when the Amp Loop is engaged. To enable the Amp Loop, follow these steps:

1.Press the Amp Loop button on the left side of the effects matrix. When the LED on the Amp Loop button is lit, the Amp Loop is enabled and the connected device is now in the RP1000’s effects chain. Internal Amp/Cabinets are basically bypassed when the Amp Loop is enabled.

2.Press the Amp Loop button again to turn off the Amp Loop. Internal Amp/Cabinets are now again active in the RP1000’s effects chain and the external device is bypassed.*

The Amp Loop can also be assigned to any of the 6-10 numbered footswitches for remote control operation during performance. To assign a footswitch to control the Amp Loop, follow these steps:

1.Press either Edit button until the Expression row has been selected (indicated by the Expression row’s LED lighting).

2.Rotate Knob 1 until FS6 ASN - FS10 ASN appears in the Display. This selects which footswitch you are about to change the assignment for.

3.Rotate Knob 2 until AMP LOOP appears in the Display.

4.Store your footswitch assignment to your preset.

*Note: If the Amp/Cabinet Bypass button is enabled, internal amp and cabinet effects are bypassed in all presets regardless of whether the Amp Loop is disabled.

Also, if you attempt to enable the Amp Loop without connections being made, the display will

briefly read no Loop indicating there are no connections made to the Amp Loop and the loop will not enable.

Stomp Loop

The RP1000 also has a stompbox effects loop (Stomp Loop). This loop lets you use an external effects device or effects chain with the RP1000’s signal path. The Stomp Loop has a dedicated Stomp Loop footswitch that enables and disables this loop during performance.

The Stomp Loop has the option of being inserted into two different positions in the RP1000’s signal path: Pre Amp, or Post Amp. This lets you pick where to place external effects in the loop. The placement of the Stomp Loop can be saved on a per preset basis.

To change the position of the Stomp Loop, follow these steps:

1.Press the Edit Down button so that the Expression row is selected.

2.Turn Knob 1 until STOMPPOS appears in the Display.

3.Turn Knob 2 to select one of the two different positions you want to insert the Stomp

8

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Owner’s Manual Page Table of Contents Warranty Preset Mode and Pedalboard Mode Getting AcquaintedIncluded Items About the RP1000Amp/Cabinet Bypass TunerTone Library Knob Effects Library KnobEditTMEditor/Librarian Presets Create Your Sound in Three Easy StepsAmp Gain/Effect Parameter Knob Amp Level/Effect Parameter KnobGuided Tour of the RP1000 Front PanelKnobs 1-6 From left to right Tone Library KnobEffects Library Knob Effects Level KnobMaster Volume Knob Bank Up/Down Footswitches13 -10 / Effects Footswitches Looper ButtonRear Panel Getting Started Making ConnectionsAmp Loop Stomp LoopConnection Setups Mono AmpMixer Stereo AmpsAmp Loop with Pre-Amp In Line ReturnAmp Loop using Guitar Amp’s Pre Amp Amp Loop and Stomp LoopStudio Setup Computer and Personal Monitors Preset Mode and Pedalboard Mode Applying PowerEditing/Creating Presets Editing Amp/Cabinet ModelsAmp/Cabinet Bypass Storing/Copying/Naming a Preset Press the Store button again to save the changesBlock Diagram About the EffectsEffect Definitions WahDistortion Distortion Knob Gain EditTMAmplifier Gbsn1x12 Based on a ‘60 Gibson GA- 40 Jensen Speaker Noise Gate/Auto Swell Chorus/FXChorus Flanger Chorus KnobFlanger Knob DepthPhaser Phaser KnobVibrato viBRaTo Rotary Speaker RotaryVibroPan vibropan Unicord Uni-VibeTMunovibeTremolo/Panner Envelope Filter eNvfiltr DOD FX25 fx25 envAutoYa Auto YA YaYa ya yaStep Filter stepfltr Sample Hold smplholdDigiTech Whammy wHammy WhammyTMPitch Shift PitCH Detune DetUNeHarmony Pitch Shifting harmony Delay Delay KnobBoss OC-2 OctaverTM octaver Reverb Reverb TypesReverb Knob Footswitch Assign Expression PedalLFOs Expression Update Factory ResetWah Min/Max Expression Pedal CalibrationPreset Level BypassLooper Page USB Setup TunerPage Wahs CompressorsNoise Gates Chorus Stompbox Models FlangerPhasers PitchVibrato / Rotary TremoloDelays Envelope / SpecialReverbs DistortionsBoss DS-1 Distortion Boss MT-2 Metal ZoneBoss OD-1 Overdrive Boss SD-1 OverdriveAmps ‘77 Marshall Master Volume ‘65 Fender Blackface Deluxe Reverb’59 Gibson GA-40 ‘69 Hiwatt Custom 100 DR103DigiTech Blackbass ’65 Blackface preamp w/ Bassman poweramp DigiTech Bright CleanDigiTech Clean Tube ’95 Matchless ChieftainDigiTech Tweedface Tweed preamp w/Blackface poweramp DigiTech GSP2101TM Artist Clean TubeDigiTech Crunch DigiTech DarkmetalCabinets 4x12 ‘96 VHT Slant w/ Celestion Vintage 30’s 4x12 ‘07 Mesa/Boogie Rectifier w/Celestion Vintage 30’s2x12 DigiTech Bright 4x12 DigiTech Alt RockSpecifications Tone Library Effects LibraryWindows Software Requirements Mac Software RequirementsDigiTech South Sandy Parkway Sandy, Utah PH 801 FAX 801
Top Page Image Contents