DigiTech RP1000 Editing/Creating Presets, Editing Amp/Cabinet Models, Amp/Cabinet Bypass

Page 19

Editing/Creating Presets

The easiest way to start editing presets is with the Tone Library and Effects Library knobs. Try out some of the tones in the Tone Library and then try out some effects setups with the Effects Library knob. Use the Effects Level Knob to increase or decrease the overall Chorus/FX, Delay and Reverb levels if desired. Once you find a tone that’s pretty close to what you want, use the Edit buttons to navigate through the individual effects to make some adjust- ments.The steps below go into more detail about how this works.

1. Select a tone

2. Select an effect

3. Adjust the

with the

or effects chain with the

effects level with the

Tone Library knob

Effects Library knob

Effects Level knob

To edit and create a preset:

1.Use the Up, Down and numbered Footswitches to select the preset you wish to edit.

2.If you find a preset close to what you want, you can begin editing the effect parameters by pressing the Edit Up/Down buttons and selecting the Effect row you want to edit.

3.If you are trying to find something different from the existing presets, begin by using the Tone Library, Effects Library and Effects Level knobs to get close to a sound you want.

4.Press the Edit Up/Down buttons to begin selecting the individual Effects rows to edit their parameters.

5.To bypass or enable an Effect row, press the Tone Library knob.

6.Use the Knobs 2-6to modify the effect parameter settings.

Note: Anytime a stored value within a preset is changed, the Store button LED lights up. This indicates that you need to store the changes. Changing presets, or turning the power off before storing any changes, erases any changes made and the RP1000 will revert to the stored values for the preset.

Also, if you are using the RP1000 with the Amp/Cabinet Bypass button enabled (effects only), Tone Libraries that use amps only will not provide distortion or tone changes since amps and cabinets are globally disabled.

Editing Amp/Cabinet Models

Each RP1000 preset has a ton of world class amp and cabinet models to choose from. To edit amp and cabinet models, follow these steps:

1.Press the Edit Down button until the Amp/Cabinet row is selected. The row’s LED should be lit and the current amp model should be shown in the display.

2.Turn Knob 1 to select from the different amp models.

3.Press Knob 1. The current cabinet model will now be displayed. Turn Knob 1 to select from the different cabinet models. Pressing Knob 1 again will return you to the amp model display

4.To bypass amp/cabinet models in a preset, turn Knob 1, fully clockwise until direct ap- pears in the RP1000’s main display, or enable the Amp/Cabinet Bypass button.

Amp/Cabinet Bypass

The RP1000 has the unique feature of being able to turn off amp and cabinet modeling globally in all presets. This feature is extremely useful when you just want to add effects processing to your own core amplifier sound. The RP1000 basically becomes a straight multi-effects box where only Wah, Compressor, Distortion, Equalizer, Noise Gate, Chorus/FX, Delay, Reverb and any effects connected to the Stomp Loop are the only effects being used.

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Owner’s Manual Page Table of Contents Warranty About the RP1000 Preset Mode and Pedalboard ModeGetting Acquainted Included ItemsEffects Library Knob Amp/Cabinet BypassTuner Tone Library KnobAmp Level/Effect Parameter Knob EditTMEditor/Librarian PresetsCreate Your Sound in Three Easy Steps Amp Gain/Effect Parameter KnobFront Panel Guided Tour of the RP1000Effects Level Knob Knobs 1-6 From left to rightTone Library Knob Effects Library KnobLooper Button Master Volume KnobBank Up/Down Footswitches 13 -10 / Effects FootswitchesRear Panel Stomp Loop Getting StartedMaking Connections Amp LoopMono Amp Connection SetupsStereo Amps MixerReturn Amp Loop with Pre-Amp In LineAmp Loop and Stomp Loop Amp Loop using Guitar Amp’s Pre AmpStudio Setup Computer and Personal Monitors Applying Power Preset Mode and Pedalboard ModeEditing Amp/Cabinet Models Editing/Creating PresetsAmp/Cabinet Bypass Press the Store button again to save the changes Storing/Copying/Naming a PresetWah Block DiagramAbout the Effects Effect DefinitionsDistortion EditTM Distortion Knob GainAmplifier Gbsn1x12 Based on a ‘60 Gibson GA- 40 Jensen Speaker Chorus/FX Noise Gate/Auto SwellChorus Depth FlangerChorus Knob Flanger KnobRotary Speaker Rotary PhaserPhaser Knob Vibrato viBRaToUnicord Uni-VibeTMunovibe VibroPan vibropanTremolo/Panner YaYa ya ya Envelope Filter eNvfiltrDOD FX25 fx25 env AutoYa Auto YAWhammyTM Step Filter stepfltrSample Hold smplhold DigiTech Whammy wHammyDetune DetUNe Pitch Shift PitCHHarmony Pitch Shifting harmony Delay Knob DelayBoss OC-2 OctaverTM octaver Reverb Types ReverbReverb Knob Expression Pedal Footswitch AssignLFOs Expression Pedal Calibration Expression UpdateFactory Reset Wah Min/MaxBypass Preset LevelLooper Page Tuner USB SetupPage Compressors WahsNoise Gates Flanger Chorus Stompbox ModelsPitch PhasersTremolo Vibrato / RotaryEnvelope / Special DelaysDistortions ReverbsBoss SD-1 Overdrive Boss DS-1 DistortionBoss MT-2 Metal Zone Boss OD-1 OverdriveAmps ‘69 Hiwatt Custom 100 DR103 ‘77 Marshall Master Volume‘65 Fender Blackface Deluxe Reverb ’59 Gibson GA-40’95 Matchless Chieftain DigiTech Blackbass ’65 Blackface preamp w/ Bassman powerampDigiTech Bright Clean DigiTech Clean TubeDigiTech Darkmetal DigiTech Tweedface Tweed preamp w/Blackface powerampDigiTech GSP2101TM Artist Clean Tube DigiTech CrunchCabinets 4x12 DigiTech Alt Rock 4x12 ‘96 VHT Slant w/ Celestion Vintage 30’s4x12 ‘07 Mesa/Boogie Rectifier w/Celestion Vintage 30’s 2x12 DigiTech BrightSpecifications Mac Software Requirements Tone LibraryEffects Library Windows Software RequirementsDigiTech South Sandy Parkway Sandy, Utah PH 801 FAX 801
Top Page Image Contents