DigiTech RP1000 owner manual Tuner, USB Setup

Page 39

If using the optional FS3X to control the Looper, follow these steps for on the fly use:

1.Start playing your guitar.

2.To begin looping, press the Down footswitch. The Looper will start recording as soon as you press the Down footswitch, and the Record LED on the matrix will light red after about half a second.

3.To set the loop point, press the Down footswitch again. The loop point will be set and the recorded phrase will now begin playback. The Record LED will turn off and the green Play LED will now be lit.

4.To add overdubs to the loop, press the Down footswitch again. The yellow Overdub LED will now light (the green Play LED will still be lit) indicating that anything being played will be merged with the loop being played.

5.Press the Down footswitch again to stop overdub recording which will turn off the Over- dub LED and return the loop to normal playback.

6.To stop loop playback, press the Up (right) footswitch. This does not clear out the loop but simply stops playback. Pressing the Down (left) footswitch again will resume playback.

7.To clear a loop from memory, press and hold the Mode (left) footswitch until the main display shows LOOPCLRD.

Tuner

The RP1000 features a built-in chromatic tuner with variable tuning references (427-453,A=Ab, A=G,A=Gb). To use the tuner, follow these steps:

1.Press and hold the currently active preset’s footswitch to access the Tuner for 2 seconds. The display briefly flashes TUNER.

2.To begin tuning, play a note on your guitar (a harmonic at the 12th fret usually works best).

3.The numeric display shows the note being played, and the alpha-numeric display indicates whether the note is sharp or flat.Arrows to the left (<<<) indicate the note is sharp and should be tuned down.Arrows to the right (>>>) indicate the note is flat and should be tuned up.When your note is in tune, -><- is displayed.

4.To exit the Tuner, press any numbered footswitch.

While the tuner is selected, you can set your tuning reference with Knob 1.The default fac- tory setting is A=440 Hz.The tuning references range from 427 Hz to 453 Hz (± 50 cents (1/2 semitone) from either direction of 440 Hz). Below 427 Hz, are alternate dropped tunings.The alternate tunings are REF A(A=Ab), REF G(A=G), and REF G(A=Gb).The display window briefly flashes the selected tuning preference.

USB Setup

The RP1000 features a USB jack which connects it to a computer. The USB jack serves two pur- poses: Streaming audio to and from a computer recording software application, and as a connec- tion for use with the X-Edit editor librarian software (downloadable from www.digitech.com).

See www.digitech.com for free X-Edit and driver downloads.

Note: PC users must download and install the ASIO driver to use the included Cubase® LE4 recording software.

There are two parameters in the effects matrix for adjusting USB parameters; USB Record Level and USB Playback Mix

USB Record Level – This option provides a digital level control for boosting or cutting the level sent to your recording application. Range is -12dB to +24dB.

USB Playback Mix – This option controls the playback mix between RP1000 processing and USB playback from your computer’s recording application. The range for this control is from USB Mix 0% (all that is heard is the RP1000 processing, no playback) to USB = RP (both USB playback

35

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Owner’s Manual Page Table of Contents Warranty About the RP1000 Preset Mode and Pedalboard ModeGetting Acquainted Included ItemsEffects Library Knob Amp/Cabinet BypassTuner Tone Library KnobAmp Level/Effect Parameter Knob EditTMEditor/Librarian PresetsCreate Your Sound in Three Easy Steps Amp Gain/Effect Parameter KnobFront Panel Guided Tour of the RP1000Effects Level Knob Knobs 1-6 From left to rightTone Library Knob Effects Library KnobLooper Button Master Volume KnobBank Up/Down Footswitches 13 -10 / Effects FootswitchesRear Panel Stomp Loop Getting StartedMaking Connections Amp LoopMono Amp Connection SetupsStereo Amps MixerReturn Amp Loop with Pre-Amp In LineAmp Loop and Stomp Loop Amp Loop using Guitar Amp’s Pre AmpStudio Setup Computer and Personal Monitors Applying Power Preset Mode and Pedalboard ModeEditing/Creating Presets Editing Amp/Cabinet ModelsAmp/Cabinet Bypass Press the Store button again to save the changes Storing/Copying/Naming a PresetWah Block DiagramAbout the Effects Effect DefinitionsDistortion EditTM Distortion Knob GainAmplifier Gbsn1x12 Based on a ‘60 Gibson GA- 40 Jensen Speaker Noise Gate/Auto Swell Chorus/FXChorus Depth FlangerChorus Knob Flanger KnobRotary Speaker Rotary PhaserPhaser Knob Vibrato viBRaToVibroPan vibropan Unicord Uni-VibeTMunovibeTremolo/Panner YaYa ya ya Envelope Filter eNvfiltrDOD FX25 fx25 env AutoYa Auto YAWhammyTM Step Filter stepfltrSample Hold smplhold DigiTech Whammy wHammyPitch Shift PitCH Detune DetUNeHarmony Pitch Shifting harmony Delay Delay KnobBoss OC-2 OctaverTM octaver Reverb Reverb TypesReverb Knob Footswitch Assign Expression PedalLFOs Expression Pedal Calibration Expression UpdateFactory Reset Wah Min/MaxPreset Level BypassLooper Page Tuner USB SetupPage Wahs CompressorsNoise Gates Flanger Chorus Stompbox ModelsPitch PhasersTremolo Vibrato / RotaryEnvelope / Special DelaysDistortions ReverbsBoss SD-1 Overdrive Boss DS-1 DistortionBoss MT-2 Metal Zone Boss OD-1 OverdriveAmps ‘69 Hiwatt Custom 100 DR103 ‘77 Marshall Master Volume‘65 Fender Blackface Deluxe Reverb ’59 Gibson GA-40’95 Matchless Chieftain DigiTech Blackbass ’65 Blackface preamp w/ Bassman powerampDigiTech Bright Clean DigiTech Clean TubeDigiTech Darkmetal DigiTech Tweedface Tweed preamp w/Blackface powerampDigiTech GSP2101TM Artist Clean Tube DigiTech CrunchCabinets 4x12 DigiTech Alt Rock 4x12 ‘96 VHT Slant w/ Celestion Vintage 30’s4x12 ‘07 Mesa/Boogie Rectifier w/Celestion Vintage 30’s 2x12 DigiTech BrightSpecifications Mac Software Requirements Tone LibraryEffects Library Windows Software RequirementsDigiTech South Sandy Parkway Sandy, Utah PH 801 FAX 801
Top Page Image Contents