DigiTech RP1000 owner manual Knobs 1-6 From left to right, Tone Library Knob, Effects Library Knob

Page 9

8. Knobs 1-6 (From left to right)

These six knobs perform various functions, depending on which mode is currently active and what (if anything) is being edited.The functions are listed below:

Tone Library (Knob 1)

1.In Performance mode, this knob selects from a library of preset amp tones.

2.When editing a preset, this knob changes the Amp or Effect model for the selected row and pressing the knob will turn the effect row on or off. When editing an Effect row, press this knob to turn the effect on or off. When editing the Amp/Cabinet row, pressing this knob will switch between editing the amp model or the cabinet model.

3.When the Expression row is selected, this knob selects the Expression Pedal, LFO 1, and LFO 2 parameter links, footswitch 6-10 assignments,Wah pedal range, Expression Pedal update, and Stomp Loop position.

*NOTE: the assignments selected for footswitches 6-10 are only available when the Pedal- board button is active.

Effects Library (Knob 2)

1.In Performance mode, this knob selects from a library of preset effect chains.

2.When editing a preset, this knob modifies the parameter listed in the column directly above it for the selected Effect row.

3.When the Expression row is selected, this knob selects which parameter is assigned to the Expression Pedal, footswitches 6-10*, and LFO1or LFO2.

*NOTE: the assignments selected for footswitches 6-10 are only available when the Pedal- board button is active.

Effects Level (Knob 3)

1.In Performance mode, this knob adjusts the overall level of post amp model effects (Chorus/FX, Delay, and Reverb).

2.When editing a preset, this knob modifies the parameter listed in the column directly above it for the selected Effect row.

3.When the Expression row is selected, this knob selects the heel value for the pa- rameter linked to the Expression Pedal or the off state are parameters assigned to footswitches 6-10*.

*NOTE: the assignments selected for footswitches 6-10 are only available when the Pedal- board button is active.

Amp Gain (Knob 4)

1.In Performance mode, this knob adjusts the Amp Gain (distortion) for the selected Amp model.

2.When editing a preset, this knob modifies the parameter listed in the column directly above it for the selected Effect row. This knob also is used to adjust the RP/USB mix when the RP1000 is connected to a computer and using recording software. Just select the Wah row to adjust this parameter when USB is connected to the RP1000.

3.When the Expression row is selected, this knob selects the toe value for the param- eter linked to the Expression Pedal Expression Pedal or the on state are parameters assigned to footswitches 6-10*.

*NOTE: the assignments selected for footswitches 6-10 are only available when the Pedal- board button is active.

Amp Level (Knob 5)

1.In Performance mode, this knob adjusts the Amp Level (volume) of the selected Amp model.

2.When editing a preset, this knob modifies the parameter listed in the column directly above it for the selected Effect row. This knob is also used to adjust the USB Record Level when the RP1000 is connected to a computer and using recording software. Just

5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Owner’s Manual Page Table of Contents Warranty Getting Acquainted Preset Mode and Pedalboard ModeIncluded Items About the RP1000Tuner Amp/Cabinet BypassTone Library Knob Effects Library KnobCreate Your Sound in Three Easy Steps EditTMEditor/Librarian PresetsAmp Gain/Effect Parameter Knob Amp Level/Effect Parameter KnobFront Panel Guided Tour of the RP1000Tone Library Knob Knobs 1-6 From left to rightEffects Library Knob Effects Level KnobBank Up/Down Footswitches Master Volume Knob13 -10 / Effects Footswitches Looper ButtonRear Panel Making Connections Getting StartedAmp Loop Stomp LoopMono Amp Connection SetupsStereo Amps MixerReturn Amp Loop with Pre-Amp In LineAmp Loop and Stomp Loop Amp Loop using Guitar Amp’s Pre AmpStudio Setup Computer and Personal Monitors Applying Power Preset Mode and Pedalboard ModeEditing/Creating Presets Editing Amp/Cabinet ModelsAmp/Cabinet Bypass Press the Store button again to save the changes Storing/Copying/Naming a PresetAbout the Effects Block DiagramEffect Definitions WahDistortion EditTM Distortion Knob GainAmplifier Gbsn1x12 Based on a ‘60 Gibson GA- 40 Jensen Speaker Noise Gate/Auto Swell Chorus/FXChorus Chorus Knob FlangerFlanger Knob DepthPhaser Knob PhaserVibrato viBRaTo Rotary Speaker RotaryVibroPan vibropan Unicord Uni-VibeTMunovibeTremolo/Panner DOD FX25 fx25 env Envelope Filter eNvfiltrAutoYa Auto YA YaYa ya yaSample Hold smplhold Step Filter stepfltrDigiTech Whammy wHammy WhammyTMPitch Shift PitCH Detune DetUNeHarmony Pitch Shifting harmony Delay Delay KnobBoss OC-2 OctaverTM octaver Reverb Reverb TypesReverb Knob Footswitch Assign Expression PedalLFOs Factory Reset Expression UpdateWah Min/Max Expression Pedal CalibrationPreset Level BypassLooper Page Tuner USB SetupPage Wahs CompressorsNoise Gates Flanger Chorus Stompbox ModelsPitch PhasersTremolo Vibrato / RotaryEnvelope / Special DelaysDistortions ReverbsBoss MT-2 Metal Zone Boss DS-1 DistortionBoss OD-1 Overdrive Boss SD-1 OverdriveAmps ‘65 Fender Blackface Deluxe Reverb ‘77 Marshall Master Volume’59 Gibson GA-40 ‘69 Hiwatt Custom 100 DR103DigiTech Bright Clean DigiTech Blackbass ’65 Blackface preamp w/ Bassman powerampDigiTech Clean Tube ’95 Matchless ChieftainDigiTech GSP2101TM Artist Clean Tube DigiTech Tweedface Tweed preamp w/Blackface powerampDigiTech Crunch DigiTech DarkmetalCabinets 4x12 ‘07 Mesa/Boogie Rectifier w/Celestion Vintage 30’s 4x12 ‘96 VHT Slant w/ Celestion Vintage 30’s2x12 DigiTech Bright 4x12 DigiTech Alt RockSpecifications Effects Library Tone LibraryWindows Software Requirements Mac Software RequirementsDigiTech South Sandy Parkway Sandy, Utah PH 801 FAX 801
Top Page Image Contents