Carrier Access Adit 3500 quick start Reset Button, RS-232 Craft Port Female DB-9, RJ-11 Connector

Page 21

Quick Start Guide

Reset Button

RS-232 Craft Port (Female DB-9)

The RS-232 craft port connector (female) is for connection to an external PC or Hayes-compatible modem for local or remote configuration, management, and performance monitoring using the Adit 3500 Command Line Interface (CLI).

The RS-232 craft port connects via a female DB-9 connector on the Adit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

5

3500.

 

 

 

 

 

 

 

 

 

6

9

 

 

 

 

 

 

 

 

 

 

 

 

The pinouts are as follows:

Pin

1

2

3

4

5

6

7

8

9

Direction

Description

Outbound

Carrier Detect

Outbound

Receive Data

Inbound

Transmit Data

Inbound

Data Terminal Ready

N/A

Signal Ground

Outbound

Data Set Ready

Inbound

Request to Send

Outbound

Clear to Send

N/C

Not connected

 

 

RJ-11 Connector

There are four RJ-11 (female) connectors for the FXS ports.

The pinouts are as follows:

 

 

 

6

1

Pin

Name

Description

 

 

1 - 2

N/C

Not connected

 

 

 

 

 

 

 

3

R

Ring

 

 

 

 

 

 

 

4

T

Tip

 

 

 

 

 

 

 

5 - 6

N/C

Not connected

 

 

 

 

 

 

 

Reset Button

The system can be reset by pressing the reset button located on the front panel.

Adit 3500 - Release 1.6

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Adit Page Quick Start Guide Unpacking and Inspection Electrostatic Discharge ESD PrecautionsUser Safety Installation EnvironmentWall Mounting Rack Mounting Battery Backup InstallationCompliant Installation Ferrite beads shipped with Adit chassis Ferrite BeadsWall Mounting See Installation Environment onTo rack mount the Adit 3000, follow the instructions below Rack MountingTray Slide Installation Battery Backup#1 Adit 3500 mounted on top of the Battery Backup Attach power cords Attach Adit 3500 to the assembled BBU and brackets3500 Mount the Battery Backup to the wall with 4 #6 screws, by #2 Adit 3500 and Battery Backup mounted to the wallChassis Overview Adit 3500 Battery Backup Power ConnectorFront BackGrounding the Unit Interface ConnectorsFront of Adit Back of AditBattery Connection VAC Power ConnectionSpecification InputDS1/E1 RJ-48C DS1/E1 Connection PortsPin Name Description State DescriptionEthernet RJ-45 10/100Base-TX EthernetRJ-11 Connector Reset ButtonRS-232 Craft Port Female DB-9 Pin Direction DescriptionCritical Alarm/Status LEDsCommand Description To access the management consoleWeb-Based Management #show interface ethernet 2 Eth WANSet the New-line/Transmit value CR+LF Setting up a CLI ConnectionLog Key Enabled Software FeaturesKey Enabled Software Features Setup Adit 3500 for access via Web-Browser Basic ConfigurationSelect Restore Defaults Restore Factory DefaultsModify Default Admin User Quick Start Guide Single T1 PPP Configure WAN Interface for Internet ConnectivitySet the proper Framing Type and Line Coding Quick Start Guide Quick Start Guide Multiple T1s Multilink Set the proper Framing Type and Line Coding Select click New Connection to create the ML-PPP connection Enter User Name and Password Quick Start Guide Quick Start Guide Ethernet WAN Quick Start Guide Configure the Adit 3500 as a SIP Gateway Select Use SIP Proxy and enter SIP Proxy IP address On the IP Telephony tab, under Proxy ServersQuick Start Guide Quick Start Guide Repeat this step for each FXS Line Quick Start Guide Set the Signaling Type Quick Start Guide Quick Start Guide Basic Configuration Adit 3500 Release
Top Page Image Contents