Carrier Access Adit 3500 quick start Installation Environment, User Safety

Page 5

Quick Start Guide

Installation Environment

Installation Environment

The environment in which you are installing the Adit 3000 must meet the following conditions:

zOperating temperature range: 32° to 104° F (0° to 40° C)

zStorage temperature range: -40°to 158° F (-40°to 70° C)

zMaximum operating altitude: 10,000 ft. (3,048 m)

zMaximum non-operating altitude: 40,000 ft. (12,192 m)

zRelative humidity (non-condensing) range: 0 to 95%

WARNING! THE ADIT 3000 IS DESIGNED FOR WALL AND RACK MOUNTING ONLY. IT IS NOT DESIGNED FOR DESKTOP USE.

User Safety

CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:

zDo not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

zAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

zDo not use the telephone to report a gas leak in the vicinity of the leak.

zUse only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

zRefer to the installation section of this manual for a safe and proper installation procedure. All wiring external to this equipment should follow the current provision of the National Electrical Code.

Adit 3500 - Release 1.6

5

Image 5
Contents Adit Page Quick Start Guide Unpacking and Inspection Electrostatic Discharge ESD PrecautionsUser Safety Installation EnvironmentWall Mounting Rack Mounting Battery Backup InstallationCompliant Installation Ferrite beads shipped with Adit chassis Ferrite BeadsWall Mounting See Installation Environment onTo rack mount the Adit 3000, follow the instructions below Rack MountingTray Slide Installation Battery Backup#1 Adit 3500 mounted on top of the Battery Backup 3500 Attach power cordsAttach Adit 3500 to the assembled BBU and brackets Mount the Battery Backup to the wall with 4 #6 screws, by #2 Adit 3500 and Battery Backup mounted to the wallChassis Overview Adit 3500 Battery Backup Power ConnectorFront BackGrounding the Unit Interface ConnectorsFront of Adit Back of AditBattery Connection VAC Power ConnectionSpecification InputDS1/E1 RJ-48C DS1/E1 Connection PortsPin Name Description State DescriptionEthernet RJ-45 10/100Base-TX EthernetRJ-11 Connector Reset ButtonRS-232 Craft Port Female DB-9 Pin Direction DescriptionCritical Alarm/Status LEDsCommand Description To access the management consoleWeb-Based Management #show interface ethernet 2 Eth WANSet the New-line/Transmit value CR+LF Setting up a CLI ConnectionLog Key Enabled Software FeaturesKey Enabled Software Features Setup Adit 3500 for access via Web-Browser Basic ConfigurationSelect Restore Defaults Restore Factory DefaultsModify Default Admin User Quick Start Guide Single T1 PPP Configure WAN Interface for Internet ConnectivitySet the proper Framing Type and Line Coding Quick Start Guide Quick Start Guide Multiple T1s Multilink Set the proper Framing Type and Line Coding Select click New Connection to create the ML-PPP connection Enter User Name and Password Quick Start Guide Quick Start Guide Ethernet WAN Quick Start Guide Configure the Adit 3500 as a SIP Gateway Select Use SIP Proxy and enter SIP Proxy IP address On the IP Telephony tab, under Proxy ServersQuick Start Guide Quick Start Guide Repeat this step for each FXS Line Quick Start Guide Set the Signaling Type Quick Start Guide Quick Start Guide Basic Configuration Adit 3500 Release