Carrier Access Adit 3500 quick start Alarm/Status LEDs, Critical

Page 22

Quick Start Guide

Alarm/Status LEDs

Alarm/Status LEDs

LED

State

Description

Critical

Off

No critical alarms present

 

 

 

 

Red

Critical alarms present. Critical alarms include:

 

 

user-configured manor environmental inputs.

 

 

 

Major

Off

No major alarms present

 

 

 

 

Red

Major alarm present. Major alarms include:

 

 

user-configured manor environmental inputs, DS1 short, DS1 open, DS1

 

 

facility alarm, DS1 RAI, DS1 AIS, DS1 LOF, DS1 LOS, WAN fault,

 

 

Ethernet fault and dead card alarms.

 

 

 

Minor

Off

No minor alarms present

 

 

 

 

Red

Minor alarms present. Minor alarms include:

 

 

user-configured manor environmental inputs, DS1 excessive line code

 

 

violations.

 

 

 

Status

Off

No power to system

 

 

 

 

Green

Application running, no detected system problems.

 

 

 

 

Green Flashing

Power-On Self Test (POST) successful. System booted. Loading Application.

 

 

 

 

Green/Yellow

Flashing alternate colors. Application Self Test in Process.

 

 

 

 

Yellow

Yellow while booting. If this stays a steady yellow the Power-On Self Test

 

 

(POST) failed.

 

 

 

 

Yellow Flashing

Power-On Self Test (POST) In Process.

 

 

 

 

Red

System Failure

 

 

 

22

Adit 3500 - Release 1.6

Image 22
Contents Adit Page Quick Start Guide Electrostatic Discharge ESD Precautions Unpacking and InspectionInstallation Environment User SafetyInstallation Wall Mounting Rack Mounting Battery BackupCompliant Installation Ferrite Beads Ferrite beads shipped with Adit chassisSee Installation Environment on Wall MountingRack Mounting To rack mount the Adit 3000, follow the instructions belowTray Slide Battery Backup Installation#1 Adit 3500 mounted on top of the Battery Backup Attach Adit 3500 to the assembled BBU and brackets Attach power cords3500 #2 Adit 3500 and Battery Backup mounted to the wall Mount the Battery Backup to the wall with 4 #6 screws, byFront Adit 3500 Battery Backup Power ConnectorChassis Overview BackFront of Adit Interface ConnectorsGrounding the Unit Back of AditSpecification VAC Power ConnectionBattery Connection InputPin Name Description DS1/E1 Connection PortsDS1/E1 RJ-48C State Description10/100Base-TX Ethernet Ethernet RJ-45RS-232 Craft Port Female DB-9 Reset ButtonRJ-11 Connector Pin Direction DescriptionAlarm/Status LEDs CriticalWeb-Based Management To access the management consoleCommand Description #show interface ethernet 2 Eth WANSetting up a CLI Connection Set the New-line/Transmit value CR+LFKey Enabled Software Features LogKey Enabled Software Features Basic Configuration Setup Adit 3500 for access via Web-BrowserRestore Factory Defaults Select Restore DefaultsModify Default Admin User Quick Start Guide Configure WAN Interface for Internet Connectivity Single T1 PPPSet the proper Framing Type and Line Coding Quick Start Guide Quick Start Guide Multiple T1s Multilink Set the proper Framing Type and Line Coding Select click New Connection to create the ML-PPP connection Enter User Name and Password Quick Start Guide Quick Start Guide Ethernet WAN Quick Start Guide Configure the Adit 3500 as a SIP Gateway On the IP Telephony tab, under Proxy Servers Select Use SIP Proxy and enter SIP Proxy IP addressQuick Start Guide Quick Start Guide Repeat this step for each FXS Line Quick Start Guide Set the Signaling Type Quick Start Guide Quick Start Guide Basic Configuration Adit 3500 Release