Emerson Process Management MSL600 manual PIN parameter P740, Fixed parameters D750 to D753

Page 45

Installation, Operation & Maintenance Manual

IP262/Z0, Rev. AB

February 2012

MSL600

7.10.6.4Date format - P734

The format for the date can be chosen from a list:

yy/mm/dd

dd/mm/yy (Default metric)

mm/dd/yy (Default imperial)

7.10.6.5Keypad Sound - P735

Each time a key is pressed, a beep sounds as confirmation of the key being pressed. This audio feedback can be turned off. The default is on.

7.10.6.6Language - P737

The HMI default language is English. The user can chose from a list of English, Francais, Deutsch, or Svenska.

7.10.7 PIN parameter P740

7.10.7.1PIN - Personal Identification Code - P740

The unit can be protected from unauthorised use by programming a PIN. Access is via SETUP – SYSTEM – PIN – PIN. Any four digit numeric characters can be programmed as a PIN. In the PIN menu enter 0000 to remove the password.

Please ensure that the PIN is not forgotten. If the password is forgotten, the factory must be consulted. Please provide the full serial number of the unit which can normally be found on the external label.

7.10.8 FIXED parameters D750 to D753

7.10.8.1Model Code - D750

The model code of the control unit.

7.10.8.2Serial No. - D751

The serial number of the control unit.

7.10.8.3H/W Revision - D752

The hardware revision of the control unit.

7.10.8.4S/W Version - D753

The software revision. This is displayed to one decimal place. Performing the Display test function (section Error! Reference source not found.) will show the full software version.

Page 45

Image 45

Contents MSL600 Installation, Operation & Maintenance ManualContents MSL600 12.2 12.1Before Operating this Device the Manual should be Read Fully About this Manual About the MSL600Self-cleaning Important MSL600 featuresHuman Machine Interface Mounting bracketLocation As a systemApplication planning Circular clarifiersRotating bridge Static bridge Rectangular clarifiersPreliminary checks InstallationLocation Mounting bracket attachmentAttaching the MSL600 Installing the bracket on the bridgeMSL600 mounting Transducer connections Power and other electrical connectionsExternal connection terminals Cable extension Display ProgrammingKeypad and Menu Navigation Contrast viewing angle controlOn-line/Off-line SecurityTank depth Bottom reference Quick start parametersDetermination of tank depth Transducer self-cleaningMA current output parameters Current output adjustAlarm Relay parametersTransducer out-of-water time Digital input Menu structure Detailed operationMain menu item Menu Item DescriptionDirect access Parameter editingScrolling Installation parameters Application parametersMain menu parameters Description P240 De-sludge parametersStart On P250 Stop On P251Start Time P253 Stop If P252Interval P254 Max Retries P257MA output parameters Cleaning parameters4 0/4-20mA P403 Alarm Action P402Relay RL1 mode P410 and RL2 mode P420 Alarm mode relay RL1 and RL2 parameters P540 toTable B Relay Parameter numbers Set point mode relay RL1 and RL2 Fault mode relay RL1 and RL2 parameters P560 to P570De-sludge mode relay RL1 and RL2 On mode relay RL1 and RL2Relay On and Off Points Display parameters HMIRelay overrides Min ON, Max ON, and Min OFF HMI upper, middle, and lower display optionsBacklight On/Off P575 Clear TrendClear Profile Logging parameters Low Mem Alarm P593Log Interval P590 Fast log P591Engineering parameters Parameter values Default Min Max 128 10241 Alg. Select P620 Common algorithm parameters P621 to P629Parameter values Default Min Max 9999 Upr S-nat Temp P625 Parameter values Default Min Max 100 Top Blanking P623Default Min Max +85 105 185 Noise Alrm Lev P622Default metric m/s Default Min Max +85 185 SoS constant P627Lwr S-nat Temp P626 Bottom Blanking P628Municipal 1 parameters P630 to P637 Parameter values Default Min Max Lost Echo Rnge P633Significance P630 Sharp Echo Reject P631Parameter values Default Min Max Lost Echo Time P637 Parameter values Default Min Max Dirty Mult P636Parameter values Default Min Max 255 Noise SD Mult P635Municipal 2 parameter P640 Parameter values Default Min Max 100Threshld Offset P640 Threshold level = Threshld Offset P640 + Noise Level D834System parameters Load Defaults functionAuto Cycle function Display testComms parameters P710 to P716 Settings parameters P730 to P737 and Base Units selectionFixed parameters D750 to D753 PIN parameter P740Readings parameters D800 to D834 Readings and diagnostics parametersDiagnostics parameters D835 to D852 Speed of Sound D850 Max Xdr Temp D851Min Xdr Temp D852 Troubleshooting MaintenanceTechnical reference Transmit pulse and echo processingSub-menu Level Parameter Title Par No Main Menu Option Programming chartProgramming chart … Direct 12.1 MSL600 SpecificationModel No OutputsWeight Additional specification notes12.2 MSL603 transducer MSL600 Bridge mounted unit Dimensional drawingsMSL600 and MSL603 assembly MSL603 transducer cable extension Parts requiredFitting instructions MSL600 MSL600 Emerson Process Management Rosemount Measurement