Grandstream Networks user manual Configuration Guide, Configuring GXW40XX VIA Voice Prompt

Page 18

CONFIGURATION GUIDE

CONFIGURING GXW40XX VIA VOICE PROMPT

DHCP MODE

Select voice menu option 01 to enable GXW40XX to use DHCP.

STATIC IP MODE

Select voice menu option 01 to enable GXW40XX to use STATIC IP mode, then use option 02, 03, 04, 05 to set up IP address, Subnet Mask, Gateway and DNS server respectively.

FIRMWARE SERVER IP ADDRESS

Select voice menu option 13 to configure the IP address of the firmware server.

CONFIGURATION SERVER IP ADDRESS

Select voice menu option 14 to configure the IP address of the configuration server.

UPGRADE PROTOCOL

Select voice menu option 15 to choose firmware and configuration upgrade protocol. User can choose between TFTP and HTTP.

FIRMWARE UPGRADE MODE

Select voice menu option 17 to choose firmware upgrade mode among the following three options: 1) always check, 2) check when pre/suffix changes, and 3) never upgrade

WAN PORT WEB ACCESS (Note: This option is not present on GXW4024 gateway)

Select voice menu option 12 to enable WAN Port Wed Access of the device configuration pages.

CONFIGURING GXW40XX WITH WEB BROWSER

The GXW40XX series gateway has an embedded Web server that allows users to configure the GXW40XX through a web browser.

ACCESS THE WEB CONFIGURATION MENU

The GXW40XX HTML configuration menu can be accessed via LAN or WAN port:

From the LAN port (For GXW4004/8 only)::

1.Directly connect a computer to the LAN port.

2.In Windows, open a ‘Command Prompt’ window

3.Type in “ipconfig /release”, the IP address etc. becomes 0.

4.Type in “ipconfig /renew”, the computer gets an IP address in 192.168.2.x segment by default

5.Open a web browser, type in the default gateway IP address. http://192.168.2.1. You will see the login page of the device.

From the WAN port (For GXW4004/8 only):

The WAN port HTML configuration option is disabled by default from factory. To access the HTML configuration menu from the WAN port:

1.Follow table 4 to find the WAN side IP address.

2.Open a web browser, type in the WAN side IP address – for example: http://GXW40XX -IP- Address (the GXW40XX IP-Address is the WAN IP address for the GXW40XX).

Grandstream Networks, Inc.

GXW40XX User Manual

Page 18 of 38

 

Firmware 1.0.4.2

Last Updated: 06/2011

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Grandstream Networks, Inc Table of Contents Diagram of GXW4004-8 and GXW4024 Back Panel Welcome Safety ComplianceWarranty Gateway GXW40XX OverviewConnect Your GXW40XX Gateway Equipment PackagingConnect the GXW40XX LAN WAN Reset Console Line FXS1 FXS24Display FXS port LEDs Status LED Power LED Ready LED ConsoleLAN LED WAN LED Available OFFSoftware Features Overview EMC Hardware Specification GXW4004 GXW4008 GXW4024Main Menu Basic OperationsUnderstanding GXW Voice Prompts 71-78Five Success Tips when using the Voice Prompt Placing a Phone CallCall Waiting Or Voice Prompt with option 47, then 192*168*0*160Call Hold Call TransferWAY Conferencing Instructions for 3-way conferenceHunting Group INTER-PORT Calling Pstn Pass THROUGH/LIFE Line Sending and Receiving FAXSupport Radius Protocol Call Features From the LAN port For GXW4004/8 only Configuration GuideConfiguring GXW40XX VIA Voice Prompt From the WAN port For GXW4004/8 onlyImportant Settings NAT SettingsDtmf Methods Web Port End User PasswordPreferred Vocoder Codec Telnet ServerMTZ+6MDT+5 DMZ IP FXS1 NATDND FXS2HTTP/HTTPS Password Config Server PathXML Config File Password Config File PrefixACS URL FXO Gateway Lifeline ModeFailover to FXO Gateway NTP serverAuthenticate ID Radius TimeoutConfiguration PasswordOffhook Auto-dial Hunting GroupPort# Map to FXO Port#Profile Active DNS ModeUnregister on Reboot Primary SIP ServerProxy Only SIP T1 Timeout Enable Ring-TransferDisable Bellcore Style Order Disable DtmfDisable Visual MWI Disable Call WaitingDisable Reminder Ring TimeoutUse # as Dial Key Early DialDial Plan Prefix Dial Plan Dial Plan RulesSDP VAD Saving the Configuration Changes Rebooting from RemoteConfiguration Through a Central Server Software Upgrade Instructions for local firmware upgradeConfiguration File Download Managing Firmware and Configuration File DownloadReset Button Restore Factory Default SettingFactory Reset IVR Command
Top Page Image Contents