RAD Data comm MBE10-8D, MBE10-1D operation manual Declaration of Conformity

Page 10

Declaration of Conformity

Manufacturer's Name:

RAD Data Communications Ltd.

Manufacturer's Address:

24 Raoul Wallenberg St.

 

Tel Aviv 69719

 

Israel

declares that the product:

 

Product Name:

MBE10-1, MBE10-8, MBE10-1D, MBE10-8D

conforms to the following standard(s) or other normative document(s):

EMC:

EN 55022

(1994)

Limits and methods of measurement of radio disturbance

 

 

 

characteristics of information technology equipment.

 

EN 50082-1 (1992)

Electromagnetic compatibility - Generic immunity standards

 

 

 

for residential, commercial and light industry.

Safety:

EN 60950

(1992/93)

Safety of information technology equipment, including

 

 

 

electrical business equipment.

Supplementary Information:

The product herewith complies with the requirements of the EMC Directive 89/336/EEC and the Low

Voltage Directive 73/23/EEC. The product was tested in a typical configuration.

Tel Aviv, September 18th, 1996

Haim Karshen

VP Quality

European Contact: RAD Data Communications GmbH, Otto-Hahn-Str. 28-30, 85521

Ottobrunn-Riemerling, Germany

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 10
Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty General Safety Instructions Please observe the following precautionsConnection of AC Mains General Safety PracticesConnection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures Versions OverviewGeneral MBE10-8D throughout this manualRouting and Bridging Support FeaturesApplications ManagementSecurity Quick SetupTransparent Remote-to-Remote Forwarding WAN EconomyFront Panel Physical DescriptionDual Image Flash Memory Rear PanelBridge Mode Routing ModeFunctional Description MBE10-1 Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1D OperationMBE10-8 Operation Functional Block DiagramMBE10-8D Operation LAN Interface LAN ProcessorManagement Type Connectors Link Interface Technical SpecificationsInterface Connectors LAN Interface StandardYellow On when a packet is being transmitted to the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being received from the LANTemperature Humidity To 90%, non-condensing 50 C/32 -122 FSite Requirements and Prerequisites Maintenance of this productIntroduction Technician who is aware of the hazards involvedInstallation and Setup Package ContentsEquipment Needed To configure the MBE unit Configuring MBEBridge Application MBE PCB Layout MBE Switches and Jumpers MainIL-4W Connecting the Interfaces 24D, V.35DTo connect the line Connecting the LineConnecting the LAN To connect to the LANConnecting the Power AC PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsOperating Instructions Initial SetupTo begin configuring MBE It is suggested to use 9.6 kbpsPower-off Power-onOperating MBE Operation Operating Instructions Ping Terminal Diagnostic TestAlarms and Troubleshooting To perform the ping testDebug Messages Filters Troubleshooting GuideDebugging Messages To view the Debug Messages logTo reset the MBE to the factory settings Resetting MBE to Factory SettingsTo filter the Debug Messages log Troubleshooting and Diagnostics Table A-1. Interface Signal List Female Connectors Appendix a Pin AssignmentFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Customer Response Form Excellent Good Fair Poor Very PoorOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters