RAD Data comm MBE10-8D, MBE10-1D operation manual List of Figures

Page 14

Table of Contents

List of Figures

1-1.

MBE Product 3-D View

1-4

1-2.

MBE16-8 Filtering and Forwarding in Bridge Mode

1-5

1-3.

MBE Functional Block Diagram

1-8

2-1. MBE PCB Layout

2-4

2-2.

4W Date Rate Selection

2-6

2-3.

Link Interface Card

2-7

2-4.

LAN Interface Module (UTP)

2-7

2-5.

MBE Rear Panel, V.35 Connector

2-8

2-6.

MBE Rear Panel, V.24 Connector

2-8

3-1.

MBE Front Panel

3-1

List of Tables

1-1.

Bridge Mode Product Intercompatibility

1-6

2-1.

MBE Switches and Jumpers

2-5

2-2.

MBE Four-Wire Data Rate

2-6

3-1.

Front Panel Controls and Indicators

3-1

4-1.

Troubleshooting Guide

4-2

ii

MBE Family Installation and Operation Manual

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 14
Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty General Safety Instructions Please observe the following precautionsConnection of DC Mains General Safety PracticesConnection of AC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures Versions OverviewGeneral MBE10-8D throughout this manualRouting and Bridging Support FeaturesApplications ManagementSecurity Quick SetupTransparent Remote-to-Remote Forwarding WAN EconomyFront Panel Physical DescriptionDual Image Flash Memory Rear PanelFunctional Description Routing ModeBridge Mode MBE10-1 Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1D OperationMBE10-8D Operation Functional Block DiagramMBE10-8 Operation LAN Interface LAN ProcessorManagement Type Connectors Link Interface Technical SpecificationsInterface Connectors LAN Interface StandardYellow On when a packet is being transmitted to the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being received from the LANTemperature Humidity To 90%, non-condensing 50 C/32 -122 FSite Requirements and Prerequisites Maintenance of this productIntroduction Technician who is aware of the hazards involvedEquipment Needed Package ContentsInstallation and Setup Bridge Application Configuring MBETo configure the MBE unit MBE PCB Layout MBE Switches and Jumpers MainIL-4W Connecting the Interfaces 24D, V.35DTo connect the line Connecting the LineConnecting the LAN To connect to the LANConnecting the Power AC PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsOperating Instructions Initial SetupTo begin configuring MBE It is suggested to use 9.6 kbpsOperating MBE Power-onPower-off Operation Operating Instructions Ping Terminal Diagnostic TestAlarms and Troubleshooting To perform the ping testDebug Messages Filters Troubleshooting GuideDebugging Messages To view the Debug Messages logTo filter the Debug Messages log Resetting MBE to Factory SettingsTo reset the MBE to the factory settings Troubleshooting and Diagnostics Table A-1. Interface Signal List Female Connectors Appendix a Pin AssignmentFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Customer Response Form Excellent Good Fair Poor Very PoorOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters