RAD Data comm MBE10-1D, MBE10-8D operation manual Power-on, Operating MBE, Power-off

Page 39

MBE Family Installation and Operation Manual	Chapter 3 Operation

Power-on

To power-up MBE:

1. Set the POWER switch on the rear panel to the ON position.

The POWER indicator lights up, indicating that MBE is powered on. After about 1 minute, the operational status screen appears on the terminal screen.

2. Press the <Enter> key several times to display the password prompt.

Operating MBE

To operate MBE:

1.Configure MBE according to the application (see the LAN RANger Series Configuration Guide).

2.During normal operation (when the remote workstations are active): The READY indicator lights up continuously

The Tx and Rx indicators blink occasionally The LAN and LINK error indicators remain OFF.

Power-off

To power-off MBE:

•Set the POWER switch on the rear panel to the OFF position.

Operating Instructions

3-3

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 39

Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty Please observe the following precautions General Safety InstructionsGeneral Safety Practices Connection of AC MainsConnection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures MBE10-8D throughout this manual OverviewGeneral VersionsManagement FeaturesApplications Routing and Bridging SupportWAN Economy Quick SetupTransparent Remote-to-Remote Forwarding SecurityRear Panel Physical DescriptionDual Image Flash Memory Front PanelRouting Mode Bridge ModeFunctional Description MBE10-1D Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1 OperationFunctional Block Diagram MBE10-8 OperationMBE10-8D Operation LAN Processor LAN InterfaceManagement LAN Interface Standard Technical SpecificationsInterface Connectors Type Connectors Link InterfaceYellow On when a packet is being received from the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being transmitted to the LAN50 C/32 -122 F Temperature Humidity To 90%, non-condensingTechnician who is aware of the hazards involved Maintenance of this productIntroduction Site Requirements and PrerequisitesPackage Contents Installation and SetupEquipment Needed Configuring MBE To configure the MBE unitBridge Application MBE PCB Layout Main MBE Switches and JumpersIL-4W 24D, V.35D Connecting the InterfacesTo connect to the LAN Connecting the LineConnecting the LAN To connect the lineAC Power Connecting the PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsIt is suggested to use 9.6 kbps Initial SetupTo begin configuring MBE Operating InstructionsPower-on Power-offOperating MBE Operation Operating Instructions To perform the ping test Diagnostic TestAlarms and Troubleshooting Ping TerminalTo view the Debug Messages log Troubleshooting GuideDebugging Messages Debug Messages FiltersResetting MBE to Factory Settings To reset the MBE to the factory settingsTo filter the Debug Messages log Troubleshooting and Diagnostics Appendix a Pin Assignment Table A-1. Interface Signal List Female ConnectorsFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Excellent Good Fair Poor Very Poor Customer Response FormOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters