RAD Data comm MBE10-1D, MBE10-8D operation manual Canadian Emission Requirements

Page 9

Canadian Emission Requirements

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulation.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

	Warning per EN 55022 (CISPR-22)
Warning
Warning	This is a class A product. In a domestic environment, this product may cause
	radio interference, in which case the user will be required to take adequate
	measures.


Avertissement	Cet appareil est un appareil de Classe A. Dans un environnement résidentiel, cet
Avertissement	appareil peut provoquer des brouillages radioélectriques. Dans ces cas, il peut
	être demandé à l’utilisateur de prendre les mesures appropriées.


	Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können
Achtung	bei Betrieb dieses Gerätes Rundfunkströrungen auftreten, in welchen Fällen der
	Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 9

Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty Please observe the following precautions General Safety InstructionsGeneral Safety Practices Connection of AC MainsConnection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures General OverviewVersions MBE10-8D throughout this manualApplications FeaturesRouting and Bridging Support ManagementTransparent Remote-to-Remote Forwarding Quick SetupSecurity WAN EconomyDual Image Flash Memory Physical DescriptionFront Panel Rear PanelRouting Mode Bridge ModeFunctional Description Principles of Operation Bridge Mode CompatibilityMBE10-1 Operation MBE10-1D OperationFunctional Block Diagram MBE10-8 OperationMBE10-8D Operation LAN Processor LAN InterfaceManagement Interface Connectors Technical SpecificationsType Connectors Link Interface LAN Interface StandardGreen On when packets can be transferred Green On when the unit is powered-upYellow On when a packet is being transmitted to the LAN Yellow On when a packet is being received from the LAN50 C/32 -122 F Temperature Humidity To 90%, non-condensingIntroduction Maintenance of this productSite Requirements and Prerequisites Technician who is aware of the hazards involvedPackage Contents Installation and SetupEquipment Needed Configuring MBE To configure the MBE unitBridge Application MBE PCB Layout Main MBE Switches and JumpersIL-4W 24D, V.35D Connecting the InterfacesConnecting the LAN Connecting the LineTo connect the line To connect to the LANAC Power Connecting the PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsTo begin configuring MBE Initial SetupOperating Instructions It is suggested to use 9.6 kbpsPower-on Power-offOperating MBE Operation Operating Instructions Alarms and Troubleshooting Diagnostic TestPing Terminal To perform the ping testDebugging Messages Troubleshooting GuideDebug Messages Filters To view the Debug Messages logResetting MBE to Factory Settings To reset the MBE to the factory settingsTo filter the Debug Messages log Troubleshooting and Diagnostics Appendix a Pin Assignment Table A-1. Interface Signal List Female ConnectorsFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Excellent Good Fair Poor Very Poor Customer Response FormOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters