RAD Data comm MBE10-8 Technical Specifications, LAN Interface Standard, Interface Connectors

Page 24

Chapter 1 Introduction	MBE Family Installation and Operation Manual

Product configurations and software are saved in flash memory. Two versions of the software are stored for redundancy.

1.4 Technical Specifications

LAN Interface Standard

Type

Connectors

LINK Interface/

Interface Connectors

Protocol

Data Rates

Conforms to Ethernet/IEEE 802.3 10Base5 (AUI)

10Base2 (BNC) (Thin Coax) 10BaseT (UTP)

10Base5: 15-pin D-type, female

10Base2: BNC female

10BaseT: RJ-45

V.35*: 34-pin female

V.24/RS-232*: 25-pin D-type, female

X.21: 15-pin D-type, female (through adapter cable)

V.36/RS-422: 37-pin D-type, female (through adapter cable)

RS-530: 25-pin D-type, female

4W: 5-screw terminal block

Basic Rate ISDN

("S" or "U" interface) – RJ-45 CSU/DSU: RJ-45

Note: *The interface can function as DTE or DCE.

Synchronous: HDLC-based

Asynchronous: Programmable UART

V.24/RS-232 (Synchronous): up to 64 kbps

V.24/RS-232 (Asynchronous): 2.4 to 115.2 kbps

V.35, X.21, V.36/RS-422, RS-530: up to 1.5 Mbps

4W: 16 to 768 kbps (selectable, internal clock)

DDS: up to 56 kbps

Basic Rate ISDN: 56, 64, 112, 128 kbps

1-10 Technical Specifications

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 24

Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty General Safety Instructions Please observe the following precautionsGeneral Safety Practices Connection of AC MainsConnection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures Overview GeneralVersions MBE10-8D throughout this manualFeatures ApplicationsRouting and Bridging Support ManagementQuick Setup Transparent Remote-to-Remote ForwardingSecurity WAN EconomyPhysical Description Dual Image Flash MemoryFront Panel Rear PanelRouting Mode Bridge ModeFunctional Description Bridge Mode Compatibility Principles of OperationMBE10-1 Operation MBE10-1D OperationFunctional Block Diagram MBE10-8 OperationMBE10-8D Operation LAN Interface LAN ProcessorManagement Technical Specifications Interface ConnectorsType Connectors Link Interface LAN Interface StandardGreen On when the unit is powered-up Green On when packets can be transferredYellow On when a packet is being transmitted to the LAN Yellow On when a packet is being received from the LANTemperature Humidity To 90%, non-condensing 50 C/32 -122 FMaintenance of this product IntroductionSite Requirements and Prerequisites Technician who is aware of the hazards involvedPackage Contents Installation and SetupEquipment Needed Configuring MBE To configure the MBE unitBridge Application MBE PCB Layout MBE Switches and Jumpers MainIL-4W Connecting the Interfaces 24D, V.35DConnecting the Line Connecting the LANTo connect the line To connect to the LANConnecting the Power AC PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsInitial Setup To begin configuring MBEOperating Instructions It is suggested to use 9.6 kbpsPower-on Power-offOperating MBE Operation Operating Instructions Diagnostic Test Alarms and TroubleshootingPing Terminal To perform the ping testTroubleshooting Guide Debugging MessagesDebug Messages Filters To view the Debug Messages logResetting MBE to Factory Settings To reset the MBE to the factory settingsTo filter the Debug Messages log Troubleshooting and Diagnostics Table A-1. Interface Signal List Female Connectors Appendix a Pin AssignmentFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Customer Response Form Excellent Good Fair Poor Very PoorOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters