RAD Data comm MBE10-1D, MBE10-8D operation manual Management

Page 23

MBE Family Installation and Operation Manual

Chapter 1 Introduction

 

 

Bridge Mode Filtering Block (MBE10-8 and MBE10-8D only)

In addition to MBE10-1 functions, MBE10-8 and MBE10-8D have a filtering block. The filtering block in the local MBE compares the destination address of every frame transmitted on the main LAN to the table of remote workstation addresses. The result of the filtering block comparison generates a copy/not copy frame command for the LAN processor.

If a frame is addressed to one of the remote workstations, the local MBE forwards this frame to the link. The remote MBE compares the destination address of every frame transmitted on the remote LAN with the remote workstation address table.

All frames in the remote LAN, containing destination addresses not included in the remote workstation address table, will be forwarded to the link by the remote MBE.

If the frame destination address is of the broadcast or multicast type, the filtering block compares the source address of the frame to the remote workstation address table. This source address check results in a copy/not copy command for the LAN processor.

Link Interface

The link interface provides the physical connection to either V.24/RS-232, V.35, RS-530, V.36, 4W, X.21, ISDN or DDS links. The 4W interface provides an internal short range modem with internal clock. DCE mode is provided for bench testing by V.24 and V.35 link interfaces. In DCE mode, the internal clock rate can be adjusted by selecting options from the internal clock rate setup menu (see "Internal Clock Rate Setup" in the LAN RANger Series Configuration Guide).

Main Processor and Communication Processor

The main processor controls the LAN and communication processors. It performs buffer management and transfers the frames received from the LAN for transmission to the link and vice versa.

The communication processor provides an HDLC link for transmission and reception of frames to the main processor. Error checks and retransmissions ensure an error-free link.

Power Supply

The MBE power supply provides required operating voltages. The power supply input ranges between 100 VAC to 240 VAC.

Asynchronous Control Port

The RJ-45 control port provides setup, configuration, and monitoring and download interface using an asynchronous ASCII terminal as a terminal emulator.

Management

Quick setup and configuration is performed via a terminal emulator attached to the control port, or via TELNET access to the device over the LAN or WAN.

An SNMP agent provides in-band or out-of-band management by RADview or by any other standard SNMP management station.

Software downloading is available through the control port, using XMODEM, and through the LAN or WAN using TFTP. Parameter file downloading and uploading is available through the LAN or WAN using TFTP.

Functional Description

1-9

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 23
Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty Please observe the following precautions General Safety InstructionsConnection of DC Mains General Safety PracticesConnection of AC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures MBE10-8D throughout this manual OverviewGeneral VersionsManagement FeaturesApplications Routing and Bridging SupportWAN Economy Quick SetupTransparent Remote-to-Remote Forwarding SecurityRear Panel Physical DescriptionDual Image Flash Memory Front PanelFunctional Description Routing ModeBridge Mode MBE10-1D Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1 OperationMBE10-8D Operation Functional Block DiagramMBE10-8 Operation LAN Processor LAN InterfaceManagement LAN Interface Standard Technical SpecificationsInterface Connectors Type Connectors Link InterfaceYellow On when a packet is being received from the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being transmitted to the LAN50 C/32 -122 F Temperature Humidity To 90%, non-condensingTechnician who is aware of the hazards involved Maintenance of this productIntroduction Site Requirements and PrerequisitesEquipment Needed Package ContentsInstallation and Setup Bridge Application Configuring MBETo configure the MBE unit MBE PCB Layout Main MBE Switches and JumpersIL-4W 24D, V.35D Connecting the InterfacesTo connect to the LAN Connecting the LineConnecting the LAN To connect the lineAC Power Connecting the PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsIt is suggested to use 9.6 kbps Initial SetupTo begin configuring MBE Operating InstructionsOperating MBE Power-onPower-off Operation Operating Instructions To perform the ping test Diagnostic TestAlarms and Troubleshooting Ping TerminalTo view the Debug Messages log Troubleshooting GuideDebugging Messages Debug Messages FiltersTo filter the Debug Messages log Resetting MBE to Factory SettingsTo reset the MBE to the factory settings Troubleshooting and Diagnostics Appendix a Pin Assignment Table A-1. Interface Signal List Female ConnectorsFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Excellent Good Fair Poor Very Poor Customer Response FormOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters