RAD Data comm MBE10-1D, MBE10-8D operation manual Connecting the Power, AC Power

Page 35

MBE Family Installation and Operation Manual	Chapter 2 Installation

Connecting the Power

AC Power

Supply AC power to the MBE unit through the 1.5m (5 ft) standard power cable terminated by a standard 3-prong plug. The cable is provided with the unit.

A 2A slow-blow fuse is located in the power supply unit.

To prevent electrical fire hazard, always replace the fuse with the same type and rating as indicated.

Warning

➤To connect AC power to the MBE unit:

1.Connect the power cable to the power connector on the MBE rear panel.

2.Connect the power cable to the mains outlet.

3.Set the POWER switch to ON.

Installation and Setup

2-9

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 35

Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty Please observe the following precautions General Safety InstructionsConnection of DC Mains General Safety PracticesConnection of AC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures MBE10-8D throughout this manual OverviewGeneral VersionsManagement FeaturesApplications Routing and Bridging SupportWAN Economy Quick SetupTransparent Remote-to-Remote Forwarding SecurityRear Panel Physical DescriptionDual Image Flash Memory Front PanelFunctional Description Routing ModeBridge Mode MBE10-1D Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1 OperationMBE10-8D Operation Functional Block DiagramMBE10-8 Operation LAN Processor LAN InterfaceManagement LAN Interface Standard Technical SpecificationsInterface Connectors Type Connectors Link InterfaceYellow On when a packet is being received from the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being transmitted to the LAN50 C/32 -122 F Temperature Humidity To 90%, non-condensingTechnician who is aware of the hazards involved Maintenance of this productIntroduction Site Requirements and PrerequisitesEquipment Needed Package ContentsInstallation and Setup Bridge Application Configuring MBETo configure the MBE unit MBE PCB Layout Main MBE Switches and JumpersIL-4W 24D, V.35D Connecting the InterfacesTo connect to the LAN Connecting the LineConnecting the LAN To connect the lineAC Power Connecting the PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsIt is suggested to use 9.6 kbps Initial SetupTo begin configuring MBE Operating InstructionsOperating MBE Power-onPower-off Operation Operating Instructions To perform the ping test Diagnostic TestAlarms and Troubleshooting Ping TerminalTo view the Debug Messages log Troubleshooting GuideDebugging Messages Debug Messages FiltersTo filter the Debug Messages log Resetting MBE to Factory SettingsTo reset the MBE to the factory settings Troubleshooting and Diagnostics Appendix a Pin Assignment Table A-1. Interface Signal List Female ConnectorsFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Excellent Good Fair Poor Very Poor Customer Response FormOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters