RAD Data comm MBE10-8D, MBE10-1D operation manual MBE PCB Layout

Page 30

Chapter 2 Installation	MBE Family Installation and Operation Manual

9.To enable direct connection between MBE and a UTP interface in any workstation, set the STATION/HUB Switch to STATION (see Figure 2-4). This is available only with the UTP option.

10.Replace the MBE cover.

11.Close by tightening the cover screw.

12.Proceed with the line, LAN and power connections as described below.

In certain locations where permanent excessive high voltages are present on the lines, setting JP7 to NC may render the unit unsafe for connection to unprotected telecommunication networks.

Warning

Link Interface	LAN Interface
Module	Module

AUI

BNC

UTP

EPROM

512K

128K

MAIN

LOCATION

SW1

REMOTE

RESET

SW2

Fuse

240VAC/2A

Slow-Blow

Power Supply

JP7

NC ON

CHASSIS

WATCH DOG

OFF ON

Figure 2-1. MBE PCB Layout

2-4	Installation and Setup

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 30

Contents MBE Family LAN RANger Series Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 MBE Family LAN RANger Series Limited Warranty General Safety Instructions Please observe the following precautionsGeneral Safety Practices Connection of AC MainsConnection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Declaration of Conformity Conventions Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Contents List of Figures Versions OverviewGeneral MBE10-8D throughout this manualRouting and Bridging Support FeaturesApplications ManagementSecurity Quick SetupTransparent Remote-to-Remote Forwarding WAN EconomyFront Panel Physical DescriptionDual Image Flash Memory Rear PanelRouting Mode Bridge ModeFunctional Description MBE10-1 Operation Bridge Mode CompatibilityPrinciples of Operation MBE10-1D OperationFunctional Block Diagram MBE10-8 OperationMBE10-8D Operation LAN Interface LAN ProcessorManagement Type Connectors Link Interface Technical SpecificationsInterface Connectors LAN Interface StandardYellow On when a packet is being transmitted to the LAN Green On when the unit is powered-upGreen On when packets can be transferred Yellow On when a packet is being received from the LANTemperature Humidity To 90%, non-condensing 50 C/32 -122 FSite Requirements and Prerequisites Maintenance of this productIntroduction Technician who is aware of the hazards involvedPackage Contents Installation and SetupEquipment Needed Configuring MBE To configure the MBE unitBridge Application MBE PCB Layout MBE Switches and Jumpers MainIL-4W Connecting the Interfaces 24D, V.35DTo connect the line Connecting the LineConnecting the LAN To connect to the LANConnecting the Power AC PowerInstallation Installation and Setup Front Panel Controls and Indicators Front Panel Controls and IndicatorsOperating Instructions Initial SetupTo begin configuring MBE It is suggested to use 9.6 kbpsPower-on Power-offOperating MBE Operation Operating Instructions Ping Terminal Diagnostic TestAlarms and Troubleshooting To perform the ping testDebug Messages Filters Troubleshooting GuideDebugging Messages To view the Debug Messages logResetting MBE to Factory Settings To reset the MBE to the factory settingsTo filter the Debug Messages log Troubleshooting and Diagnostics Table A-1. Interface Signal List Female Connectors Appendix a Pin AssignmentFemale DB-37 RS-530 21 / 15-pin Appendix a Pin Assignment 35/ DB-25 Figure A-4. Four-Wire 4W Connection Table A-3. Isdn S Interface Cable Pin Assignments Index Xmodem Customer Response Form Excellent Good Fair Poor Very PoorOrder from Cutter Networks Ph727-398-5252/Fax727-397-9610 Error Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters