Sony SRX- R110, SRX-R105 To install batteries, Screen SEL buttons, Lens Cont buttons

Page 12

Chapter 1 Overview

B:Selects the signal input from the connectors on the optional input board installed in the INPUT B section.

C:Selects the signal input from the connectors on the optional input board installed in the INPUT C section.

D:Selects the signal input from the connectors on the optional input board installed in the INPUT D section.

Use these buttons together with the PICTURE CONT buttons (6) or SCREEN SEL buttons (7).

Example: When you want to increase the contrast of the signal input from the INPUT A board, press INPUT SEL A button, then press the CONTR + button.

fPICTURE CONT (Picture control) buttons Adjust the projected picture quality.

CONTR+/–:Adjust the contrast. Pressing the + button increases the contrast. Pressing the – button decreases the contrast.

BRIGHT +/–:Adjust the picture brightness. Pressing the

+button makes the picture brighter. Pressing the – button makes the picture darker.

SHARP +/–:Adjust the picture sharpness. Pressing the +

button makes the picture sharper. Pressing the – button makes the picture softer.

In multiple screen mode, adjustment can be made for the input signal from each input board.

Select the input signal with the INPUT SEL A/B/C/D buttons (5), then adjust the picture with these buttons. In single-screen mode, you need not press the INPUT SEL button.

Example: When you want to increase the contrast for the

signal input from the INPUT A board, press the INPUT SEL A button, then press the CONTR + button.

gSCREEN SEL buttons

In multiple screen mode, select one of the divided screens where you want to project the selected signal from each input board.

Select the input signal with one of the INPUT SEL A/B/C/ D buttons (5), then select the screen with one of these buttons.

Example: When you want to project the signal input from the INPUT B board on Screen 3 (lower left screen), press the INPUT SEL B button, then press the SCREEN SEL 3 button.

hLENS CONT buttons

FOCUS +/–:Adjust the focus. Pressing the + button focuses on a forward picture. Pressing the – button focuses on a picture further back.

ZOOM +/–:Adjust the picture size. Pressing the + button enlarges the picture size. Pressing the – button reduces the picture size.

SHIFT +/–:Adjust the vertical picture position. Pressing the + button moves the picture upward. Pressing the – button moves the picture downward.

To install batteries

1Remove the lid, then install the two size AA (R6) batteries (supplied) with the correct polarity.

Push the knob to open

Be sure to install the battery

the lid.

from the – side.

2Replace the lid.

Notes

Be sure that there is nothing to obstruct the infrared beam between the Remote Commander and the projector. Direct the Remote Commander toward one of the remote control detectors at the front and rear of the projector when operating.

The operation range is limited. The shorter the distance between the Remote Commander and the projector, the wider the angle within which the Commander can control the projector.

GB 12

Location and Function of Controls

Image 12
Contents SR Projector For the customers in the USA For the customers in EuropePour les utilisateurs en Europe Für Kunden in EuropaTable of Contents Projecting OthersPrecautions On safetyOn installation On illuminationUsing the CD-ROM Manual On cleaningCD-ROM System Requirements Reading the CD-ROM ManualFeatures High Brightness, High Picture QualityFlexible and Reliable System Versatile Setup Various signal inputLocation and Function of Controls Optional lensLeft Side/Rear Control Function Menu WindowPassword menu Screen Control windowFile menu Back menuRemote Commander 11 GBTo install batteries Screen SEL buttonsLens Cont buttons Precautions on Installation Unsuitable Installation13 GB Using the Carrying Handles Using the AdjustersUnsuitable Conditions Blocking the ventilation holesInstalling the Projector Installing the SRX ControllerSystem Requirements 15 GBPreparations Connecting the Computer via the Ethernet Connecting the Computer via the RS-232C17 GB Changing the Connection Mode Starting the SRX ControllerStarting the SRX Controller About the Browser ScreenConnecting the Projector Connecting with HD-SDI EquipmentWhen you connect the projector, make sure to 19 GBConnecting with a Computer Using the Remote Commander Projecting the Picture21 GB When you select dual-screen mode or quad-screen mode in step Using the Computer for Controlling the Projector 23 GBTo turn off the power To cut off the pictureTo cut off the whole screen To reset the settings that have been adjusted To register the settings that have been adjusted25 GB To go back to the Browser ScreenSignal Info Information About the items that cannot be adjustedPicture Control Window Input SourceSignal Adjust COLOR/FRAME WindowColor 27 GBInstallation Window Frame AdjustAuto Lamp Select Mode Manual Lamp Select Mode29 GB Input Signals And Adjustable/Setting Items Signal AdjustFrame Adjust Lamp Life 31 GBTroubleshooting PowerRemote Commander/SRX Controller PictureError Messages 33 GBRear FAN Alert Specifications 35 GBOptional accessories Preset SignalsPin assignment Displayed image size in multiple screen mode 37 GBLamp Power Lamp Select Lens Control Index