Sony SRX- R110, SRX-R105 When you select dual-screen mode or quad-screen mode in step

Page 22
Set the main power switch to the lower position.
Note
Do not set the main power switch to the lower position while the fan is running. Doing so stops the fan before the inside of the projector has been cooled down sufficiently and may damage the unit.
2
Press the 1 button.
The STATUS LAMP indicator flashes green and the fan continues to run for 10 minutes to reduce the internal heat. When the fan stops running, the STATUS LAMP indicator lights red.
1
During adjustment, “ZOOM” appears on the screen.
8 Adjust the focus again with the FOCUS +/– buttons.
9 Adjust the vertical position of the picture with the SHIFT +/– buttons.
During adjustment, “SHIFT” appears on the screen.
Note
The FOCUS, ZOOM and SHIFT indications do not appear when you select “OSD OFF” in the Control Function Menu window of the computer.
To cut off the picture
Press the MUTING button.
To restore the picture, press the MUTING button again.
To turn off the power
Adjust the picture size with the ZOOM +/– buttons.
7
Adjust the focus with the FOCUS +/– buttons. During adjustment, “FOCUS” appears on the screen.
6
picture in dual-screen mode or the upper left screen in quad-screen mode. If you project still pictures only, you may project them on any screen.

Chapter 3 Projecting

1Set the main power switch on the left side of the projector to the upper position.

The STATUS LAMP indicator lights red and the projector goes into standby mode.

2Press the ? button to turn on the projector. The STATUS LAMP indicator lights green.

3Select the screen mode.

Each time you press the SCREEN MODE button, the screen mode switches as follows:

1(single-screen mode): Projects an image in full screen.

2 (dual-screen mode): Projects images in two divided screens. You can also project a different input source in each of the two screens.

4(quad-screen mode): Projects images in four divided screens. You can also project a different input source in each of the four screens.

4Turn on the equipment connected to the projector.

5Press the INPUT SEL button to select the input source.

A:to select the input source from the equipment connected to the optional input board attached to the INPUT A section.

B:to select the input source from the equipment connected to the optional input board attached to the INPUT B section.

C:to select the input source from the equipment connected to the optional input board attached to the INPUT C section.

D:to select the input source from the equipment connected to the optional input board attached to the INPUT D section.

When you select “dual-screen mode” or “quad-screen mode” in step 3

Press one of the INPUT SEL A to D buttons to select the input source you want to project, then select one of the divided screens where you want to project the picture with the SCREEN SEL button.

Note

When projecting moving pictures in multiple screens, all the input signals should be genlocked to synchronize with each other. A picture on the left screen for dual-screen mode or that on the upper left screen for quad-screen mode is regarded as a reference picture. The projected moving picture not synchronized with the reference picture appears incompatible with the moving pictures projected on other screens. If you project still pictures and moving pictures together, select the left screen for the moving

GB 22

Projecting the Picture

Image 22
Contents SR Projector Pour les utilisateurs en Europe For the customers in the USAFor the customers in Europe Für Kunden in EuropaTable of Contents Projecting OthersOn installation PrecautionsOn safety On illuminationCD-ROM System Requirements Using the CD-ROM ManualOn cleaning Reading the CD-ROM ManualHigh Brightness, High Picture Quality FeaturesFlexible and Reliable System Location and Function of Controls Versatile SetupVarious signal input Optional lensLeft Side/Rear Control Function Menu WindowFile menu Password menuScreen Control window Back menuRemote Commander 11 GBScreen SEL buttons To install batteriesLens Cont buttons Unsuitable Installation Precautions on Installation13 GB Unsuitable Conditions Using the Carrying HandlesUsing the Adjusters Blocking the ventilation holesSystem Requirements Installing the ProjectorInstalling the SRX Controller 15 GBPreparations Connecting the Computer via the RS-232C Connecting the Computer via the Ethernet17 GB Starting the SRX Controller Changing the Connection ModeStarting the SRX Controller About the Browser ScreenWhen you connect the projector, make sure to Connecting the ProjectorConnecting with HD-SDI Equipment 19 GBConnecting with a Computer Projecting the Picture Using the Remote Commander21 GB When you select dual-screen mode or quad-screen mode in step Using the Computer for Controlling the Projector 23 GBTo cut off the picture To turn off the powerTo cut off the whole screen 25 GB To reset the settings that have been adjustedTo register the settings that have been adjusted To go back to the Browser ScreenPicture Control Window Signal Info InformationAbout the items that cannot be adjusted Input SourceColor Signal AdjustCOLOR/FRAME Window 27 GBInstallation Window Frame AdjustManual Lamp Select Mode Auto Lamp Select Mode29 GB Signal Adjust Input Signals And Adjustable/Setting ItemsFrame Adjust Lamp Life 31 GBRemote Commander/SRX Controller TroubleshootingPower PictureError Messages 33 GBRear FAN Alert Specifications 35 GBPreset Signals Optional accessoriesPin assignment Displayed image size in multiple screen mode 37 GBLamp Power Lamp Select Lens Control Index