Belkin 5000HQ user manual Replication, Connecting the secondary unit to the network

Page 93

Maintenance of the System

Table of Contents

sections 1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18

19

20 21

16..4 Replication

You can add a secondary OmniView IP 5000HQ Manager unit to the system. The primary unit then replicates all data to the secondary unit. In the event of a failure in the primary unit, the secondary unit can take over and operate with the most up-to-date database.

16..4..1 Connecting the secondary unit to the network

1.Connect the secondary unit to a power supply outlet.

2.Connect the secondary unit to the network as follows: On the rear panel, connect an Ethernet cable to LAN 1.

3.Power up the secondary unit.

16..4..2 Configuring the secondary unit

Configure the secondary unit before configuring the primary unit. Configuration involves changing the secondary unit IP address (so as not to cause a network conflict by having the same IP address as the primary unit) and assigning the unit to be the secondary unit.

1.From the secondary unit, log in to the OmniView IP 5000HQ Manager web interface. See the “Displaying the OmniView IP 5000HQ Web Interface” section on page 12 to display the OmniView IP 5000HQ web interface.

2.Change the IP address of the secondary unit to be different to the primary unit, but ensure that it resides on the same network segment. You change the secondary unit IP address from the “Network” tab under “Settings/Unit Maintenance”. See the “Network tab” section on page 95. Once changed, the unit restarts.

3.Log in again with the new network settings.

4.From the “Settings/Maintenance” menu, click “Replication”; Figure 100 appears.

Figure 100 Replication page

5.Select “Secondary Unit”. A field for the IP address of the primary unit appears.

6.Type the primary unit IP address.

7.Click . The unit restarts in secondary unit mode.

OmniView IP 5000 HQ

89

Image 93
Contents OmniViewIP* 5000HQ Table of Contents Settings Applications Configuring Access Services for Individual TargetsSettings Attached Devices Accessing. Targets Administrator Configuring Access Services IntroductionUnit Maintenance Accessing the System as a UserIntroduction Key featuresIntroduction Pointer tab Pre-Installation GuidelinesPre-Installation Guidelines Access Services detailsAdding user-defined Access Services Figure below shows a typical OmniView IP 5000HQ application Understanding the System An OverviewUnderstanding the System An Overview Forming users into groupsCreating targets Associating a user group with a target set Forming targets into setsSame user in different groups Access ServicesUnderstanding the System An Overview Enabling HQ for OmniView IP 5XXXG series Setting Up the SystemConnecting the OmniView IP 5000HQ Manager Setting Up the SystemOmniView IP 5000HQ Manager’s default IP address Changing the OmniView IP 5000HQ Manager network parametersDevices Displaying the OmniView IP 5000HQ Web InterfaceMenu section Displaying the OmniView IP 5000HQ Web InterfaceUsers Creating UsersGeneral tab Creating UsersRemoving users from a group User Group tabNew User Access Permissions tab Access Permissions tabDeleting a user Saving a userCreating a New User Group Members tab Creating a user groupCreating New Users Access Permissions tab Allowed Services tabDeleting a user group Saving the new groupList of existing targets in the system Configuring TargetsConfiguring Targets Access Services tabDefault Access Service On the New Target page, click Assignment is removed PDU tab Assigning power outlet to targetClick and the outlet number will appear Current Target Sets tab Target Sets tabSaving the target Deleting targetsCreating a target set Current Target sets in the system Saving the target setDeleting a target set Deleting a target setManagement DevicesStatus 10 11 12 13 14 15 16 17 Other Devices Other Devices PDU ManagementFollowing commands can be performed from the HQ interface Current console servers in the system Other Devices Console ServerAdding new console servers Serial tab Advanced button Configuring the KVM IP devices in the OmniView IP 5000HQHigh PerformanceLow MediumKVM Ports tab Configuring KVM over IP KVM Ports tabKVM-over-IP Device Network tab Network tabSaving the KVM-over-IP device configuration changes Deleting KVM-over-IP devicesDevice discovery Settings Access Services Settings ApplicationsBelkin OmniView IP KVM Settings ApplicationsAccount policy Account policyStrict policy password Password policyStandard policy password Account blockingExternal authentication Ldap OmniView IP 5000HQ in external authentication Ldap modeDNS setting in Ldap mode Importing users Ldap settingsSynchronization Synchronization does two things Users must be members of groups in order to be shownGlobal settings Operating OmniView IP 5000HQ in external authentication modeOmniView IP 5000HQ session idle time-out Default power commandSet mouse and performance from KVM/IP session Items PerSettings Attached Devices 10..1 PDUUploading a new PDU model KVM switches Settings Attached DevicesConsole server Uploading a new KVM switchUploading a new serial console model Configuring Access Services Introduction Access Services default valuesGeneral note about application paths Belkin Serial Console Server Configuring Access Services Introduction11..1..4 ILO 11..1..3 WebILO Web mode Web modeWeb mode default Login MethodRDP Client mode 11..1..5 RDP11..1..6 SSH RDP RDP Client mode11..1..7 VNC VNC VNC Client modeDescription Description of the Access Service VNC Telnet VMware Server VMware ServerNew Service New Access ServicesConfiguring Access Services Introduction Targets Configuring Access Services for Individual TargetsSingle Port Console Server Configuring Access Services for Individual Targets12..1..3 ILO 12..1..2 WebWeb mode 12..1..4 RDP RDP Web mode12..1..5 SSH VNC VNC Client 12..1..6 VNCWeb mode Telnet VMware Server Access page columns Accessing Targets AdministratorPower management column Name columnMore Access Services column Accessing Targets AdministratorAccessing a target via KVM-over-IP remote session Status columnSwitching to a different server Choose to take over or view only or cancelNot default Access Service Taking over a busy remote sessionExiting the OmniView IP 5000HQ system Power column Accessing the System as a UserConnecting to a target Accessing the System as a UserChange Password window Accessing a KVM-over-IP Device Directly Backup Maintenance of the SystemMaintenance of the System Backup elementsRestoring database backup Restore Settings Restoring OmniView IP 5000HQ to factory default settingsResetting OmniView IP 5000HQ configuration Firmware upgrade Firmware upgrade Upgrading the KVM-over-IP device firmwareConnecting the secondary unit to the network Configuring the secondary unitReplication 16. ..4 Promoting a secondary unit to a standalone unit Configuring the primary unitReconfiguring the primary and secondary units Primary unit and secondary unit troubleshooting Redoing the secondary and primary unit configurationChecking the secondary unit Event Log Event logDrop-down search menus Access, System, or Configuration tabsDate & Time tab Unit MaintenancePower Control tab Unit MaintenanceAbout AboutGeneral Troubleshooting General Troubleshooting Legacy KVM port switching does not occurCannot log in to the OmniView IP 5000HQ Dimensions Technical SpecificationsWeee compliance Technical SpecificationsFCC Statement InformationF1DP101C CE Declaration of ConformityInformation 104 How state law relates to the warrantyBelkin International, Inc Belkin B..V