Belkin 5000HQ user manual Adding new console servers Serial tab

Page 40

Management

Table of Contents sections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Figure 51 Adding new console servers – Serial tab

Drag the target name from the right side’s current targets list to the left side’s corresponding serial port. Double-click on the target name on the right side to remove the selection. Repeat for each power outlet,

and clickwhen you’re done. Your console server has been configured and the console server ( ) becomes available from the “Access” tab.

Figure 52 Using console servers

8..3 Setting each OmniView KVM-over-IP Switch to be OmniView IP 5000HQ-enabled

In order to be managed by OmniView IP 5000HQ, all Belkin KVM IP devices must be configured to be HQ. See the “Setting Up the System” section on page 10.

Tip! Since KVM IP devices only appear in the “New Devices” list once they are HQ-enabled, make each KVM IP device HQ-enabled in a certain order with a suitable time gap, so that you can identify the unit’s location.

OmniView IP 5000 HQ

36

Image 40
Contents OmniViewIP* 5000HQ Table of Contents Configuring Access Services for Individual Targets Settings ApplicationsSettings Attached Devices Accessing. Targets Administrator Configuring Access Services IntroductionAccessing the System as a User Unit MaintenanceKey features IntroductionIntroduction Pre-Installation Guidelines Pointer tabAccess Services details Pre-Installation GuidelinesAdding user-defined Access Services Understanding the System An Overview Figure below shows a typical OmniView IP 5000HQ applicationForming users into groups Understanding the System An OverviewCreating targets Forming targets into sets Associating a user group with a target setAccess Services Same user in different groupsUnderstanding the System An Overview Setting Up the System Enabling HQ for OmniView IP 5XXXG seriesSetting Up the System Connecting the OmniView IP 5000HQ ManagerOmniView IP 5000HQ Manager’s default IP address Changing the OmniView IP 5000HQ Manager network parametersDisplaying the OmniView IP 5000HQ Web Interface DevicesDisplaying the OmniView IP 5000HQ Web Interface Menu sectionCreating Users UsersCreating Users General tabUser Group tab Removing users from a groupAccess Permissions tab New User Access Permissions tabSaving a user Deleting a userCreating a user group Creating a New User Group Members tabAllowed Services tab Creating New Users Access Permissions tabSaving the new group Deleting a user groupConfiguring Targets List of existing targets in the systemAccess Services tab Configuring TargetsDefault Access Service On the New Target page, click Assignment is removed Assigning power outlet to target PDU tabClick and the outlet number will appear Target Sets tab Current Target Sets tabDeleting targets Saving the targetCreating a target set Saving the target set Current Target sets in the systemDeleting a target set Deleting a target setDevices ManagementStatus Management 10 11 12 13 14 15 16 17 Other Devices Other Devices PDUFollowing commands can be performed from the HQ interface Other Devices Console Server Current console servers in the systemAdding new console servers Serial tab Configuring the KVM IP devices in the OmniView IP 5000HQ Advanced buttonPerformance HighLow MediumConfiguring KVM over IP KVM Ports tab KVM Ports tabNetwork tab KVM-over-IP Device Network tabDeleting KVM-over-IP devices Saving the KVM-over-IP device configuration changesDevice discovery Settings Applications Settings Access ServicesSettings Applications Belkin OmniView IP KVMAccount policy Account policyPassword policy Strict policy passwordStandard policy password Account blockingOmniView IP 5000HQ in external authentication Ldap mode External authentication LdapDNS setting in Ldap mode Ldap settings Importing usersUsers must be members of groups in order to be shown Synchronization Synchronization does two thingsOperating OmniView IP 5000HQ in external authentication mode Global settingsDefault power command OmniView IP 5000HQ session idle time-outSet mouse and performance from KVM/IP session Items Per10..1 PDU Settings Attached DevicesUploading a new PDU model Settings Attached Devices KVM switchesUploading a new KVM switch Console serverUploading a new serial console model Access Services default values Configuring Access Services IntroductionGeneral note about application paths Configuring Access Services Introduction Belkin Serial Console Server11..1..3 Web 11..1..4 ILOWeb mode ILO Web modeLogin Method Web mode defaultRDP Client mode 11..1..5 RDPRDP RDP Client mode 11..1..6 SSHVNC VNC Client mode 11..1..7 VNCDescription Description of the Access Service VNC Telnet VMware Server VMware ServerNew Access Services New ServiceConfiguring Access Services Introduction Configuring Access Services for Individual Targets TargetsConfiguring Access Services for Individual Targets Single Port Console Server12..1..2 Web 12..1..3 ILOWeb mode RDP Web mode 12..1..4 RDP12..1..5 SSH 12..1..6 VNC VNC VNC ClientWeb mode Telnet VMware Server Accessing Targets Administrator Access page columnsPower management column Name columnAccessing Targets Administrator More Access Services columnAccessing a target via KVM-over-IP remote session Status columnChoose to take over or view only or cancel Switching to a different serverNot default Access Service Taking over a busy remote sessionExiting the OmniView IP 5000HQ system Accessing the System as a User Power columnAccessing the System as a User Connecting to a targetChange Password window Accessing a KVM-over-IP Device Directly Maintenance of the System BackupBackup elements Maintenance of the SystemRestoring database backup Restoring OmniView IP 5000HQ to factory default settings Restore SettingsResetting OmniView IP 5000HQ configuration Firmware upgrade Upgrading the KVM-over-IP device firmware Firmware upgradeConfiguring the secondary unit Connecting the secondary unit to the networkReplication Configuring the primary unit 16. ..4 Promoting a secondary unit to a standalone unitReconfiguring the primary and secondary units Redoing the secondary and primary unit configuration Primary unit and secondary unit troubleshootingChecking the secondary unit Event log Event LogAccess, System, or Configuration tabs Drop-down search menusUnit Maintenance Date & Time tabUnit Maintenance Power Control tabAbout AboutGeneral Troubleshooting Legacy KVM port switching does not occur General TroubleshootingCannot log in to the OmniView IP 5000HQ Technical Specifications DimensionsTechnical Specifications Weee complianceInformation FCC StatementF1DP101C CE Declaration of ConformityInformation How state law relates to the warranty 104Belkin International, Inc Belkin B..V