HandHeld Entertainment SV Series Model Specifications, ScanView Software, Laser Beam, SV100

Page 12

SV Series Model Specifications

Contact Hand Held Products Technical Support for information on custom and other models.

	SV100	SV100HD	SV100C	SV200-1	SV200-2

Analyses/	100	100	100	200	200
sec

Scan	6”	4.5”	10.5”	2.5”	1.75”
Width	(152mm)	(114mm)	(267mm)	(63.5mm)	(44mm)

Focus	8”	6”	15”	8”	6”
Distance	(203mm)	(152mm)	(381mm)	(203mm)	(152mm)

X dim	.0067”	.005”	.013”	.0067”	.005”
(min)	(.17mm)	(.127mm)	(.33mm)	(.17mm)	(.127mm)

ScanView Software

The recommended setup tool for the SV Series is Hand Held Products’

ScanView Windows®-based software. This program makes SV setup simple via menus, plus it offers real time monitoring of bar codes being analyzed. This program is available from Hand Held Products and authorized Hand Held Products re-sellers. ScanView can be used to program the SV Series via serial communication using SV download language. The language is described in this user’s guide.

Laser Beam

The laser beam may be on at any time the Power/Sync LED is illuminated.

1 - 2

Quick Check® SV Series User’s Guide

Image 12

Contents User’s Guide Disclaimer Statement of Agency Compliance FCC Class B Compliance StatementCanadian Notice Statement of RoHS Compliance SV Series Use with UL-listed EquipmentLaser Beam Laser Safety Enclosure DescriptionPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Quick Check SV Series IntroductionSV Series Model Specifications ScanView SoftwareLaser Beam SV100Reset Button ConnectorControl Panel + 5 VDC Power Input Sync InputsIsolated Sync Input Diagram Edge Sync Mode Envelope Sync ModeCommunication Sync Commands Output PortsPower/Sync LED Indicator LEDs 1System Displays Calibration LEDSerial Port Connector Serial Port SpecificationsSerial Port Pin-out Serial Port Transmission FormatPos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide ScanView Installation and Setup ScanView Software InstallationSystem Requirements PC Communication Port Setup Setup Menu Software Operation WarningsTitle Bar Screen Display Menu Bar Screen DisplaySelect Symbologies Static Codes ModeMoving Codes Mode Ladder Mode and Picket Fence ModeAdvanced Menu Support MenuAbout Menu Item Speed Button Bar Screen Display All Data Points, Last 64 Data PointsZoom Erase Current Session DataTransmit SV Commands Session ModeSession Mode Notes Modes Of OperationReflectance Profile Mode Analysis ScreensBar Code Analysis Screen Bar Code Analysis Screen Bottom PanelBar Code Analysis Results for a Previous Bar Code Graph Display AreaRight Panel Color Coding Reflectance Profile ScreenReflectance Profile Screen Scanner Setup Scanner Positioning SV Scanner/Verifier Setup Procedure Bar Code Travel DirectionBar Code Travel Speed Considerations Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Picket Fence Direction Bad Reflectance ProfilePicket Fence Bar Code Positioning Specifications Setting Ladder Mode Scanning Length Using ScanView SoftwareCalibration Ladder DirectionProcedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide SV Command Language Data Match Commands B~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max Check for specific dataExamples ~ Brnbb .. + Define increment or decrement data checkIncrementing Examples Decrementing ExamplesRelationship Between ~BC and ~Br Commands Diagnostic Commands DGet the Scan Rate Hardware Configuration Commands H Example return using ScanView~HB# Example return using ScanView inputted ~HB5 ~HO# Operational Mode~HQ# Transmission Mode Display the verifier parametersQuick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset Label Setup Commands L ~LA## Overall passing grade~LD## Passing percent decode ~LFxy Analyze special subsymbology parameters ~LE#~LI# Include the specified symbology for a label ~LLQuick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LS## Set minimum number of scans for valid read ~LT# Sync Input Source~LV## Output Interface Mode ~LX# Sync Type~LZ## Set Number of Codes per Label i.e., per sync period Output Mode Selection Commands O ~OS# Set Transmission Data FormatOutput Port Setup Commands P ~PBpiiaaabbb Port barcode decision block parametersIDs Analysis Low High Units Parameters Value PCS ~PPpiiaaa Port action parameters IDs Description Low Value High ValuePort State PASS/FAIL Parameters ~PR#### Port/LED reset state Indicator Digit ValueSystem Control Commands S IndicatorHow to Set Up Single Scan Operation Checking SV Status with ~HTExecute the calibration procedure Disable VerificationEnable Verification ~SK# Communication SyncSet the number of scans for Software Commanded Read Mode Operation Description~SN### Raster CheckReset the System ~Sh## Set the high target reflectance value for calibration~Sl## Set the low target reflectance value for calibration ~Ssxy Command Example Data Transmission ExampleMode 00 ~LV00 ~Stx Program Command Indicator Header~Stx Command Example ~St5 Output Interface Modes DescriptionsMode 01 ~LV01 Mode 01 I/O operationMode 01 LED Operation SV Commands Important to Mode Mode 02 ~LV02 Mode 02 I/O operationMode 02 LED Operation ~LV02~LQ0 Mode 03 ~LV03 Mode 12 ~LV12Mode 12 I/O operation Mode 12 LED Operation ~LV12~LDxx Mode 16 ~LV16 Mode 16 I/O operationMode 16 LED Operation ~LV16~PP801xxx ~PB811xxxyyy Mode 17 ~LV17 OperationSV Commands Important for Mode LED Operation~LV17 ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Technical Specifications Qcolvsv Series Product SpecificationsParameter Specification Power Scanning Performance-SV Series ModelScanner Options SyncSymbologies Sync Mode Moving Bar CodesOperation Modes OutputsSync Mode Stationary Bar Codes Parameters AnalyzedNo Sync Free Scan Operation Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Maintenance/Customer Support MaintenanceCleaning Technical AssistanceProduct Service and Repair Online Technical Assistance For Further InformationJapan MalaysiaLimited Warranty Online Product Service and Repair AssistanceQuick Check SV Series User’s Guide Setting the Proper Scan Distance Setting the Proper Scan Angle Session Mode Screen Showing the X Dimension MeasurementButton Example of Good Scan Profile Calibration Hints Examples of Scan Profile Parameters Out of RangeQuick Check SV Series User’s Guide Page Hand Held Products, Inc