HandHeld Entertainment SV Series manual Mode 17 ~LV17, Operation

Page 90

~Hx

This command stores all parameters into non-volatile memory. This command should be the last command sent after parameters are programmed via the above commands.

Mode 17 (~LV17)

I/O operation

1.System will operate in Edge Sync or Envelope sync mode (~LX#).

2.Sync polarity programmable (~LP#)

3.Use ~PR0200 for proper port initialization.

4.Port 1 will pulse active ON for a bar code quality or data error condition.

5.Port 2 will pulse active ON for a NO READ, partial or low % decode error condition.

6.Port 3 will pulse active ON for a non-error condition.

7.Port pulse times programmable. (~PP801xxx)

8.Pulses act like re-triggerable 1-shot logic

9.Pushing the reset button or power re-cycle will place Ports 1, 2 and 3 in their inactive states and reset the # codes per sync counter.

10.Error conditions available are:

a.Partial Read (Programmable, ( ~Lp#, LQ#)

b.% decode (Programmable, ~LD##)

c.Bad Quiet Zone: < 10X (~PB816xxx100)

d.ISO Defects grade (Programmable, ~PB806xxx000)

e.ISO Decodability grade (Programmable, ~PB802xxx100)

f.Symbol Contrast grade (Programmable, ~PB804xxx100)

g.Overall ISO Grade (Programmable, ~LAxx)

h.No Read (if sync is received)

i.Number of codes per sync programmable (~LN##, ~LZ##)

j.X dimension Range (Programmable ~PB811xxxyyy)

k.Ratio (Programmable ~PB815xxx000)

l.Symbology Mod Check data error

6 - 42

Quick Check® SV Series User’s Guide

Image 90

Contents User’s Guide Disclaimer Statement of Agency Compliance FCC Class B Compliance StatementCanadian Notice Statement of RoHS Compliance SV Series Use with UL-listed EquipmentLaser Beam Laser Safety Enclosure DescriptionPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Quick Check SV Series IntroductionLaser Beam SV Series Model SpecificationsScanView Software SV100Reset Button ConnectorControl Panel + 5 VDC Power Input Sync InputsIsolated Sync Input Diagram Edge Sync Mode Envelope Sync ModeCommunication Sync Commands Output PortsSystem Displays Power/Sync LEDIndicator LEDs 1 Calibration LEDSerial Port Pin-out Serial Port ConnectorSerial Port Specifications Serial Port Transmission FormatPos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide ScanView Installation and Setup ScanView Software InstallationSystem Requirements PC Communication Port Setup Title Bar Screen Display Setup MenuSoftware Operation Warnings Menu Bar Screen DisplayMoving Codes Mode Select SymbologiesStatic Codes Mode Ladder Mode and Picket Fence ModeAdvanced Menu Support MenuAbout Menu Item Zoom Speed Button Bar Screen DisplayAll Data Points, Last 64 Data Points Erase Current Session DataSession Mode Notes Transmit SV CommandsSession Mode Modes Of OperationReflectance Profile Mode Analysis ScreensBar Code Analysis Screen Bar Code Analysis Screen Bottom PanelBar Code Analysis Results for a Previous Bar Code Graph Display AreaRight Panel Color Coding Reflectance Profile ScreenReflectance Profile Screen Scanner Setup Scanner Positioning SV Scanner/Verifier Setup Procedure Bar Code Travel DirectionBar Code Travel Speed Considerations Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Picket Fence Direction Bad Reflectance ProfileCalibration Picket Fence Bar Code Positioning SpecificationsSetting Ladder Mode Scanning Length Using ScanView Software Ladder DirectionProcedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide SV Command Language Data Match Commands B~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max Check for specific dataExamples ~ Brnbb .. + Define increment or decrement data checkIncrementing Examples Decrementing ExamplesRelationship Between ~BC and ~Br Commands Diagnostic Commands DGet the Scan Rate Hardware Configuration Commands H Example return using ScanView~HB# Example return using ScanView inputted ~HB5 ~HO# Operational Mode~HQ# Transmission Mode Display the verifier parametersQuick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset Label Setup Commands L ~LA## Overall passing grade~LD## Passing percent decode ~LFxy Analyze special subsymbology parameters ~LE#~LI# Include the specified symbology for a label ~LLQuick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LS## Set minimum number of scans for valid read ~LT# Sync Input Source~LV## Output Interface Mode ~LX# Sync Type~LZ## Set Number of Codes per Label i.e., per sync period Output Mode Selection Commands O ~OS# Set Transmission Data FormatOutput Port Setup Commands P ~PBpiiaaabbb Port barcode decision block parametersIDs Analysis Low High Units Parameters Value PCS ~PPpiiaaa Port action parameters IDs Description Low Value High ValuePort State PASS/FAIL Parameters ~PR#### Port/LED reset state Indicator Digit ValueSystem Control Commands S IndicatorHow to Set Up Single Scan Operation Checking SV Status with ~HTEnable Verification Execute the calibration procedureDisable Verification ~SK# Communication Sync~SN### Set the number of scans for Software Commanded Read ModeOperation Description Raster CheckReset the System ~Sh## Set the high target reflectance value for calibration~Sl## Set the low target reflectance value for calibration ~Ssxy Command Example Data Transmission Example~Stx Command Example ~St5 Mode 00 ~LV00~Stx Program Command Indicator Header Output Interface Modes DescriptionsMode 01 ~LV01 Mode 01 I/O operationMode 01 LED Operation SV Commands Important to Mode Mode 02 ~LV02 Mode 02 I/O operationMode 02 LED Operation ~LV02~LQ0 Mode 03 ~LV03 Mode 12 ~LV12Mode 12 I/O operation Mode 12 LED Operation ~LV12~LDxx Mode 16 ~LV16 Mode 16 I/O operationMode 16 LED Operation ~LV16~PP801xxx ~PB811xxxyyy Mode 17 ~LV17 OperationSV Commands Important for Mode LED Operation~LV17 ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Technical Specifications Qcolvsv Series Product SpecificationsParameter Specification Scanner Options PowerScanning Performance-SV Series Model SyncOperation Modes SymbologiesSync Mode Moving Bar Codes OutputsSync Mode Stationary Bar Codes Parameters AnalyzedNo Sync Free Scan Operation Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Cleaning Maintenance/Customer SupportMaintenance Technical AssistanceJapan Product Service and RepairOnline Technical Assistance For Further Information MalaysiaLimited Warranty Online Product Service and Repair AssistanceQuick Check SV Series User’s Guide Setting the Proper Scan Distance Setting the Proper Scan Angle Session Mode Screen Showing the X Dimension MeasurementButton Example of Good Scan Profile Calibration Hints Examples of Scan Profile Parameters Out of RangeQuick Check SV Series User’s Guide Page Hand Held Products, Inc