HandHeld Entertainment SV Series manual ~LV## Output Interface Mode, ~LX# Sync Type

Page 65

~LV##

Output Interface Mode

## = 00 - 99:

This command sets the output interface mode of the unit. Modes have fixed port activation logic defined by specific applications. Some activation parameters are programmable. Custom modes are available – contact Hand Held Products Technical Support. Modes included in standard SV Series are described in the "Output Interface Modes Descriptions" on page 6-30. Example: ~LV01 sets mode 01.

~LX#

Sync Type

0

1

2

3

Envelope sync

Edge sync

Envelope sync w/beam control - leading edge turns on laser, trailing edge turns off laser

Note: ~LP# sets polarity for Modes 2, 19, and 20 when ~LX2 is set.

Edge sync w/beam control - edge turns on beam, bar code exiting beam turns beam off

Note: Use ~LS02 setting for sync type ~LX3.

~LZ##

Set Number of Codes per Label (i.e., per sync period)

This command sets the exact number of codes to be read during a sync period.

##= the number of codes. For example: ~LZ02 causes a No Read condition to be set if exactly 2 bar codes are not fully decoded during a sync interval. This command can also be entered by scanning a bar code. See details in the ~LN## (page 6-14) command description.

This command overrides the ~LN## command if the number of codes set does not = 00. If ~LZ## is set to ~LZ00, the ~LN## command takes precedence.

~Lp#

Turn partials on and off at the decoder level for all symbologies.

0

1

Disable

Enable

Quick Check® SV Series User’s Guide

6 - 17

Image 65

Contents User’s Guide Disclaimer Canadian Notice Statement of Agency ComplianceFCC Class B Compliance Statement Laser Beam Statement of RoHS ComplianceSV Series Use with UL-listed Equipment Enclosure Description Laser SafetyPage Table of Contents Scanner Setup ISO Parameter Grade Thresholds Technical Specifications Chapter a SV Series Setup Hints Scanning Distance and Angle Introduction Quick Check SV SeriesScanView Software SV Series Model SpecificationsLaser Beam SV100Control Panel Reset ButtonConnector Sync Inputs + 5 VDC Power InputIsolated Sync Input Diagram Envelope Sync Mode Edge Sync ModeOutput Ports Communication Sync CommandsIndicator LEDs 1 Power/Sync LEDSystem Displays Calibration LEDSerial Port Specifications Serial Port ConnectorSerial Port Pin-out Serial Port Transmission FormatPos Chars Parameters + or indicating sign of avg. max. bar Symbology Identifier Table UPC-A Quick Check SV Series User’s Guide System Requirements ScanView Installation and SetupScanView Software Installation PC Communication Port Setup Software Operation Warnings Setup MenuTitle Bar Screen Display Menu Bar Screen DisplayStatic Codes Mode Select SymbologiesMoving Codes Mode Ladder Mode and Picket Fence ModeAbout Menu Item Advanced MenuSupport Menu All Data Points, Last 64 Data Points Speed Button Bar Screen DisplayZoom Erase Current Session DataSession Mode Transmit SV CommandsSession Mode Notes Modes Of OperationBar Code Analysis Screen Reflectance Profile ModeAnalysis Screens Bottom Panel Bar Code Analysis ScreenRight Panel Bar Code Analysis Results for a Previous Bar CodeGraph Display Area Reflectance Profile Screen Color CodingReflectance Profile Screen Scanner Setup Scanner Positioning Bar Code Travel Speed Considerations SV Scanner/Verifier Setup ProcedureBar Code Travel Direction Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Good Reflectance Profile Bad Reflectance Profile Picket Fence DirectionSetting Ladder Mode Scanning Length Using ScanView Software Picket Fence Bar Code Positioning SpecificationsCalibration Ladder DirectionProcedure Adjusting Scanner Gain and Offset Desired Signal Amplitude and Placement Quick Check SV Series User’s Guide Data Match Commands B SV Command LanguageCheck for specific data ~BCa##bc…bbb……mmm……bbb…… etc. up to 32 characters max~ Brnbb .. + Define increment or decrement data check ExamplesDecrementing Examples Incrementing ExamplesGet the Scan Rate Relationship Between ~BC and ~Br CommandsDiagnostic Commands D ~HB# Hardware Configuration Commands HExample return using ScanView ~HO# Operational Mode Example return using ScanView inputted ~HB5Display the verifier parameters ~HQ# Transmission ModeQuick Check SV Series User’s Guide ~Hdx01nnn Sets scanner gain or offset ~LD## Passing percent decode Label Setup Commands L~LA## Overall passing grade ~LE# ~LFxy Analyze special subsymbology parameters~LL ~LI# Include the specified symbology for a labelQuick Check SV Series User’s Guide ~LQ# Enable or Disable Port Activations by Partial Decodes ~LT# Sync Input Source ~LS## Set minimum number of scans for valid read~LZ## Set Number of Codes per Label i.e., per sync period ~LV## Output Interface Mode~LX# Sync Type ~OS# Set Transmission Data Format Output Mode Selection Commands OIDs Analysis Low High Units Parameters Value Output Port Setup Commands P~PBpiiaaabbb Port barcode decision block parameters PCS IDs Description Low Value High Value ~PPpiiaaa Port action parametersPort State PASS/FAIL Parameters Indicator Digit Value ~PR#### Port/LED reset stateIndicator System Control Commands SChecking SV Status with ~HT How to Set Up Single Scan OperationDisable Verification Execute the calibration procedureEnable Verification ~SK# Communication SyncOperation Description Set the number of scans for Software Commanded Read Mode~SN### Raster Check~Sl## Set the low target reflectance value for calibration Reset the System~Sh## Set the high target reflectance value for calibration Data Transmission Example ~Ssxy Command Example~Stx Program Command Indicator Header Mode 00 ~LV00~Stx Command Example ~St5 Output Interface Modes DescriptionsMode 01 LED Operation Mode 01 ~LV01Mode 01 I/O operation SV Commands Important to Mode Mode 02 I/O operation Mode 02 ~LV02~LV02 Mode 02 LED Operation~LQ0 Mode 12 I/O operation Mode 03 ~LV03Mode 12 ~LV12 ~LV12 Mode 12 LED Operation~LDxx Mode 16 I/O operation Mode 16 ~LV16~PP801xxx Mode 16 LED Operation~LV16 ~PB811xxxyyy Operation Mode 17 ~LV17~LV17 SV Commands Important for ModeLED Operation ~PB815xxx000 Mode 18 ~LV18 LED Operation ~LV18 ~PB806xxx000 Mode 19 ~LV19 ~LV19 ~LDxx Mode 20 ~LV20 ISO Parameter Grade Thresholds Reference Decode Parameter Specification Technical SpecificationsQcolvsv Series Product Specifications Scanning Performance-SV Series Model PowerScanner Options SyncSync Mode Moving Bar Codes SymbologiesOperation Modes OutputsNo Sync Free Scan Operation Sync Mode Stationary Bar CodesParameters Analyzed Quick Check SV Series User’s Guide Quick Check SV Series User’s Guide Maintenance Maintenance/Customer SupportCleaning Technical AssistanceOnline Technical Assistance For Further Information Product Service and RepairJapan MalaysiaOnline Product Service and Repair Assistance Limited WarrantyQuick Check SV Series User’s Guide Setting the Proper Scan Distance Session Mode Screen Showing the X Dimension Measurement Setting the Proper Scan AngleButton Example of Good Scan Profile Examples of Scan Profile Parameters Out of Range Calibration HintsQuick Check SV Series User’s Guide Page Hand Held Products, Inc