Energy Tech Laboratories EDP70 manual Start UP

Page 41

7.0START UP

1.Switch on the AC reserve and the main AC Utility supply to the UPS.

2.Turn on the Utility supply Input, Reserve Input (if fitted) and UPS Output switches located behind the front panel, see figure 14 for 24kVA, figure 17 for 36kVA or figure 20 for 50/80kVA.

3.Replace the front panel.

4.Press the CANCEL AUDIBLE ALARM switch (see section 6.2)

5.Initially, all the green indicators will flash on the display mimic. After about 30 seconds the supply and battery indicators should stop flashing.

6.Press the Inverter On push button (I).

7.The inverter should now start and after a delay of approximately 30 seconds the message ‘SYSTEM NORMAL’, in English, will appear on the liquid crystal display.


8. Select the required language by pressing page right control		until the ‘SELECT LANGUAGE’
message appears on the liquid crystal display. Press the page down control			until the required
language is selected. Press the page right control	once more confirm the language selection.
Thereafter, all messages will appear in the selected language.

MI00/10056 rev.1--05/2001-- page 41

Image 41

Contents EDP70 Plus Important Safety Instructions Read Before Installing ALL CASES, Seek Medical Attention Immediately Contents Figures Introduction Block diagramSummary of the manual Summary of the equipment24kVA Standard Configuration 480V Functions24/36kVA Ratings Operational modes10 --MI00/10056 rev.1--05/2001 Symbols SafetyGeneral safety Battery safety equipment Electrical precautionsBattery precautions Storage InstallationMechanical characteristics ALL Measurements are Millimeters and Inches NR4 16 --MI00/10056 rev.1--05/2001 Battery Cabinet Drawing for 24/36kVA Ratings 18 --MI00/10056 rev.1--05/2001 Battery Cabinet Drawing for 50/80kVA Ratings 20 --MI00/10056 rev.1--05/2001 Installation Recommended wire sizes Supply Output Reserve Supply UPS Type = 2770 - - - ∙ e 0.125 h Tk / T0 Tr Tk VentilationOutput ConnectionUninterruptible Power System No Unauthorized Operation MI00/10056 rev.1--05/2001-- Electrical connections Table of T& B’s cat.no.s for terminals and crimp tools24 12/18/24kVA Battery CompartmentOutput, Reserve, Input Reserve Ground Primary Input Output External Batteries 36 24/30/36kVA Observe Polarities and Orientations RS232 Female EDP70 Plus 50/80kVA 36 --MI00/10056 rev.1--05/2001 QS1 QS2 QS3 QS4 QS5 Emergency Power Off Signal connections Battery charge inhibited Thermostick connector 50/80kVA onlyUser Controls Display indicatorsControls LCD Control PanelStart UP SHUT-DOWN Maintenance BypassInstalling the EPO MI00/10056 rev.1--05/2001-- Silencing Audible Alarm Visual and Audible AlarmsMimic Liquid Crystal DisplaySystem Normal Display Page HeadingsBattery Test Weekly Power History Down to Access Load Time on Reserve xxg xxh xxm xxs Inverter Load System Alarm Abnormal operating mode messagesStop DUE to Overload RECTIFIER/BATTERY Alarms Message Condition Inverter Alarms Message Condition LOAD/RESERVE Alarms Message Condition Power History Matrix Power HistoryResetting data loss manually Battery TestBattery Autonomy Test MI00/10056 rev.1--05/2001-- 11.1 AS400 Computer Interface11.2 RS232 Remote AlarmsBatteries 13.1 EDP70 PLUS/24/18/12 Battery Installation/Start-up13.2 EDP70 PLUS/24/18/12 Optional Battery Cubicle = EDP70 PLUS/24/18/12 Internal Battery Shelves13.4 EDP70 Plus above 20kVA Battery Cubicle Maintenance and Spare Parts13.3 EDP70 Plus above 20kVA Battery Installation/Start-up EDP70 Plus System LOG