Dell R805 manual Removing and Installing a RAC Card

Page 42

5. Disconnect the two short ribbon cables to the RAC card. See Figure 3-20.

Figure 3-20. Removing and Installing a RAC Card

1

standoff holes (2)

2

RAC-card connectors (2)

3

RAC-card cables (2)

4

RAC card

 

 

 

 

5

support standoff

6

cutout

 

 

 

 

7

retention standoffs (2)

 

 

 

 

 

 

6.Pull back slightly on one of the blue retention standoff tabs and gently work the edge of RAC card off of the standoff. Repeat for the other retention standoff.

7.Angle the free end of the RAC card up and pull the card away from the support standoff.

8.If you are not replacing the RAC card, disconnect and remove the ribbon cables from the system board and insert the plastic filler plug in the system back panel.

NOTICE: When detaching the RAC cables from the system board, squeeze the metal ends of the cable connectors and gently work the connector out of the socket. Do not pull on the cable to unseat the connector. Doing so can damage the cable.

9.Reinstall expansion-card riser 1. See Replacing Expansion-Card Riser 1.

10.Reinstall all expansion cards in expansion-card riser 1. See Installing an Expansion Card.

11.Close the system. See Closing the System.

Installing a RAC Card

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2.Open the system. See Opening the System.

3.Remove all expansion cards from expansion-card riser 1. See Removing an Expansion Card.

4.Remove expansion-card riser 1. See Removing Expansion-Card Riser 1.

5.If you are installing a RAC card for the first time, remove the plastic filler plug from the system back panel. See Figure 3-20.

6.Angle the RAC card so that its NIC connector inserts through the back- panel RAC card opening, and then straighten the card.

7.Position the back edge of the card so that the cutout on the edge of the card inserts into the support standoff. See Figure 3-20.

8.Align the front edge of the RAC card with the two front plastic retention standoffs and press down the side of the card until it is fully seated on the

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Page Back to Contents Accessing System Features During StartupKeystrokes for Accessing System Features Other Information You May NeedFront-Panel Features and Indicators Indicator, Button, or Icon Description ConnectorHard-Drive Indicator Patterns for RAID Back-Panel Features and IndicatorsHard-Drive Indicator Codes Condition Drive-Status Indicator PatternConnecting External Devices Power Indicator CodesNIC Indicator Codes Redundant Power Supply IndicatorsLCD Status Messages NIC Indicator CodesIndicator Indicator Code LCD Status MessagesTroubleshooting the Microprocessors See Troubleshooting System Cooling ProblemsTroubleshooting System Cooling Problems See Troubleshooting the MicroprocessorsSee Troubleshooting System Memory See Troubleshooting a Hard DriveInstall memory. See Installing Memory Modules Daughter CardRemoving LCD Status Messages Solving Problems Described by LCD Status MessagesSystem Messages System MessagesTroubleshooting Your System for any faulty components Troubleshooting System MemorySee Installing a RAC Card Troubleshooting a Hard Drive. See Using the System SetupCombination. See Installing a Processor USB Device, or Troubleshooting a Hard Drive forSee Troubleshooting a USB Device or Troubleshooting a Hard See Troubleshooting the System BatteryDiagnostics Messages Alert MessagesBack to Contents When to Use the System Diagnostics Using Server Administrator DiagnosticsSystem Diagnostics Features Running the System DiagnosticsSelecting Diagnostics Options Using the Custom Test OptionsSelecting Devices for Testing System Diagnostics Testing OptionsContacting Dell Contacting DellVisit support.dell.com Glossary Page Page System memory See RAM Back to Contents Installing System Components Recommended Tools Inside the SystemFront Bezel Replacing the Front Bezel Opening and Closing the SystemRemoving the Front Bezel Opening the SystemHard Drives Closing the SystemRemoving a Drive Blank Installing a Drive BlankInstalling a Hot-Plug Hard Drive Removing a Hot-Plug Hard DriveInstalling a Hard Drive Into a Drive Carrier Replacing a Hard-Drive CarrierRemoving a Hard Drive From a Hard-Drive Carrier Power Supplies Removing a Power SupplyInstalling the Power Supply Blank Replacing a Power SupplyRemoving the Power Supply Blank Internal SD CardInstalling the SD Card System FansRemoving a System Fan Installing a SAS Controller Daughter Card SAS Controller Daughter CardReplacing a Cooling Fan Removing a SAS Controller Daughter Card 11. SAS Controller Daughter Card CablingInternal USB Memory Key Connector RAID BatteryConfiguring the Boot Device Installing a RAID BatteryInstalling the Optional Internal USB Memory Key Expansion CardsExpansion Card Installation Guidelines Installing an Expansion CardRemoving an Expansion Card Cooling Shrouds Removing the Memory Module Cooling ShroudsInstalling the Processor Cooling Shroud Installing the Memory Module Cooling ShroudsRemoving the Processor Cooling Shroud Fan Brackets Removing the Fan BracketsReplacing the Fan Bracket Expansion-Card Risers Removing Expansion-Card RiserReplacing Expansion-Card Riser Removing the Riser 2 Board From the Expansion-Card Bracket 18. Removing and Replacing Expansion-Card RiserRAC Card Replacing the Riser 2 Board on the Expansion-Card BracketRemoving the RAC Card Installing a RAC Card 20. Removing and Installing a RAC CardLOM Daughter Card Removing the LOM Daughter CardReplacing the LOM Daughter Card Installing the Optical DriveOptical Drive Removing the Optical Drive from the System22. Removing and Installing the Optical Drive Tray Removing the Optical Drive From the Optical Drive TrayMemory Configurations Installing an Optical Drive Into the Optical Drive TrayGeneral Memory Module Installation Guidelines System MemoryInstalling Memory Modules Memory Sparing ConfigurationsMemory Sparing Support 25. Installing and Removing a Memory Module Removing Memory ModulesIntegrated NIC TOE ProcessorsRemoving a Processor Installing a Processor 26. Installing and Removing the Heat SinkSystem Battery Replacing the System BatterySideplane Board Removing the Sideplane BoardInstalling the Sideplane Board SAS/SATA Backplane BoardRemoving the SAS/SATA Backplane Board Control Panel Assembly Installing the SAS/SATA Backplane BoardRemoving the Control Panel Assembly Installing the Control Panel AssemblySystem Board Removing the System BoardInstalling the System Board Replace the sideplane. See Installing the Sideplane BoardJumper Setting Description System Board JumpersSystem Board Connectors Connector DescriptionSAS/SATA Backplane Board Connectors Sideplane Board ConnectorsDisabling a Forgotten Password Expansion-Card Riser-Board Components and PCIe BusesOpen the system. See Opening and Closing the System Back to Contents Responding to Error Messages Entering the System Setup ProgramSystem Setup Options Using the System Setup ProgramMemory Information Screen System Setup Program OptionsUsing the System Password and Using the Setup Password Memory Information ScreenCPU Information Screen Integrated Devices ScreenCPU Information Screen Integrated Devices Screen Options Serial Communication ScreenSystem Security Screen Serial Communication Screen OptionsDisabled System and Setup Password FeaturesEnabled Exit ScreenUsing the System Password Assigning a System PasswordUsing the Setup Password Deleting or Changing an Existing System PasswordBMC Setup Module Options Baseboard Management Controller ConfigurationEntering the BMC Setup Module See Disabling a Forgotten PasswordStart-Up Routine Safety First-For You and Your SystemTroubleshooting IRQ Assignment Conflicts Checking the EquipmentIRQ Assignment Defaults Troubleshooting External ConnectionsTroubleshooting the Video Subsystem IRQ Line AssignmentTroubleshooting Basic I/O Functions Troubleshooting the KeyboardTroubleshooting the Mouse Troubleshooting a Serial I/O Device Troubleshooting a USB DeviceTroubleshooting a NIC Troubleshooting a Wet SystemClose the system. See Opening and Closing the System Troubleshooting a Damaged System Troubleshooting the System BatteryTroubleshooting Power Supplies Troubleshooting System Cooling ProblemsTroubleshooting System Memory Troubleshooting a FanTroubleshooting an SD Card or Internal USB Key Troubleshooting an Optical Drive Troubleshooting an External Tape DriveTroubleshooting a Hard Drive Remove the bezel. See Removing the Front BezelTroubleshooting a SAS Controller Daughter Card Troubleshooting Expansion Cards Troubleshooting the Microprocessors
Related manuals
Manual 200 pages 56.14 Kb
Top Page Image Contents