Dell R805 Entering the System Setup Program, System Setup Options, Responding to Error Messages

Page 63

Back to Contents Page

Using the System Setup Program

Dell™ PowerEdge™ R805 Systems Hardware Owner's Manual

Entering the System Setup Program

System Setup Options

System and Setup Password Features

Disabling a Forgotten Password

Baseboard Management Controller Configuration

After you set up your system, run the System Setup program to familiarize yourself with your system configuration and optional settings. Record the information for future reference.

You can use the System Setup program to:

Change the system configuration stored in NVRAM after you add, change, or remove hardware

Set or change user-selectable options—for example, the time or date

Enable or disable integrated devices

Correct discrepancies between the installed hardware and configuration settings

Entering the System Setup Program

1.Turn on or restart your system.

2.Press <F2> immediately after you see the following message:

<F2> = System Setup

If your operating system begins to load before you press <F2>, allow the system to finish booting, and then restart your system and try again.

NOTE: To ensure an orderly system shutdown, see the documentation that accompanied your operating system.

Responding to Error Messages

You can enter the System Setup program by responding to certain error messages. If an error message appears while the system is booting, make a note of the message. Before entering the System Setup program, see System Messages for an explanation of the message and suggestions for correcting errors.

NOTE: After installing a memory upgrade, it is normal for your system to send a message the first time you start your system.

Using the System Setup Program

Table 2-1 lists the keys that you use to view or change information on the System Setup program screens and to exit the program.

Table 2-1. System Setup Program Navigation Keys

Keys

Action

 

 

Up arrow or <Shift><Tab>

Moves to the previous field.

 

 

Down arrow or <Tab>

Moves to the next field.

Spacebar, <+>, <–>, left and right arrows

Cycles through the settings in a field. In many fields, you can also type the appropriate value.

 

 

<Esc>

Exits the System Setup program and restarts the system if any changes were made.

 

 

<F1>

Displays the System Setup program's help file.

 

 

NOTE: For most of the options, any changes that you make are recorded but do not take effect until you restart the system.

System Setup Options

Main Screen

When you enter the System Setup program, the main System Setup program screen appears (see Figure 2-1).

Image 63
Contents Page Other Information You May Need Accessing System Features During StartupKeystrokes for Accessing System Features Back to ContentsIndicator, Button, or Icon Description Connector Front-Panel Features and IndicatorsCondition Drive-Status Indicator Pattern Back-Panel Features and IndicatorsHard-Drive Indicator Codes Hard-Drive Indicator Patterns for RAIDRedundant Power Supply Indicators Power Indicator CodesNIC Indicator Codes Connecting External DevicesLCD Status Messages NIC Indicator CodesIndicator Indicator Code LCD Status MessagesSee Troubleshooting the Microprocessors See Troubleshooting System Cooling ProblemsTroubleshooting System Cooling Problems Troubleshooting the MicroprocessorsDaughter Card See Troubleshooting a Hard DriveInstall memory. See Installing Memory Modules See Troubleshooting System MemorySystem Messages Solving Problems Described by LCD Status MessagesSystem Messages Removing LCD Status MessagesTroubleshooting a Hard Drive. See Using the System Setup Troubleshooting System MemorySee Installing a RAC Card Troubleshooting Your System for any faulty componentsSee Troubleshooting the System Battery USB Device, or Troubleshooting a Hard Drive forSee Troubleshooting a USB Device or Troubleshooting a Hard Combination. See Installing a ProcessorAlert Messages Diagnostics MessagesBack to Contents Running the System Diagnostics Using Server Administrator DiagnosticsSystem Diagnostics Features When to Use the System DiagnosticsSystem Diagnostics Testing Options Using the Custom Test OptionsSelecting Devices for Testing Selecting Diagnostics OptionsContacting Dell Contacting DellVisit support.dell.com Glossary Page Page System memory See RAM Back to Contents Installing System Components Recommended Tools Inside the SystemFront Bezel Opening the System Opening and Closing the SystemRemoving the Front Bezel Replacing the Front BezelClosing the System Hard DrivesRemoving a Hot-Plug Hard Drive Installing a Drive BlankInstalling a Hot-Plug Hard Drive Removing a Drive BlankInstalling a Hard Drive Into a Drive Carrier Replacing a Hard-Drive CarrierRemoving a Hard Drive From a Hard-Drive Carrier Removing a Power Supply Power SuppliesInternal SD Card Replacing a Power SupplyRemoving the Power Supply Blank Installing the Power Supply BlankInstalling the SD Card System FansRemoving a System Fan Installing a SAS Controller Daughter Card SAS Controller Daughter CardReplacing a Cooling Fan 11. SAS Controller Daughter Card Cabling Removing a SAS Controller Daughter CardInstalling a RAID Battery RAID BatteryConfiguring the Boot Device Internal USB Memory Key ConnectorExpansion Cards Installing the Optional Internal USB Memory KeyExpansion Card Installation Guidelines Installing an Expansion CardRemoving an Expansion Card Removing the Memory Module Cooling Shrouds Cooling ShroudsInstalling the Processor Cooling Shroud Installing the Memory Module Cooling ShroudsRemoving the Processor Cooling Shroud Fan Brackets Removing the Fan BracketsReplacing the Fan Bracket Expansion-Card Risers Removing Expansion-Card RiserReplacing Expansion-Card Riser 18. Removing and Replacing Expansion-Card Riser Removing the Riser 2 Board From the Expansion-Card BracketRAC Card Replacing the Riser 2 Board on the Expansion-Card BracketRemoving the RAC Card 20. Removing and Installing a RAC Card Installing a RAC CardRemoving the LOM Daughter Card LOM Daughter CardRemoving the Optical Drive from the System Installing the Optical DriveOptical Drive Replacing the LOM Daughter CardRemoving the Optical Drive From the Optical Drive Tray 22. Removing and Installing the Optical Drive TraySystem Memory Installing an Optical Drive Into the Optical Drive TrayGeneral Memory Module Installation Guidelines Memory ConfigurationsInstalling Memory Modules Memory Sparing ConfigurationsMemory Sparing Support Removing Memory Modules 25. Installing and Removing a Memory ModuleIntegrated NIC TOE ProcessorsRemoving a Processor 26. Installing and Removing the Heat Sink Installing a ProcessorReplacing the System Battery System BatteryRemoving the Sideplane Board Sideplane BoardInstalling the Sideplane Board SAS/SATA Backplane BoardRemoving the SAS/SATA Backplane Board Installing the SAS/SATA Backplane Board Control Panel AssemblyInstalling the Control Panel Assembly Removing the Control Panel AssemblyRemoving the System Board System BoardReplace the sideplane. See Installing the Sideplane Board Installing the System BoardSystem Board Jumpers Jumper Setting DescriptionConnector Description System Board ConnectorsSideplane Board Connectors SAS/SATA Backplane Board ConnectorsDisabling a Forgotten Password Expansion-Card Riser-Board Components and PCIe BusesOpen the system. See Opening and Closing the System Back to Contents Using the System Setup Program Entering the System Setup ProgramSystem Setup Options Responding to Error MessagesMemory Information Screen System Setup Program OptionsUsing the System Password and Using the Setup Password Memory Information ScreenCPU Information Screen Integrated Devices ScreenCPU Information Screen Serial Communication Screen Options Serial Communication ScreenSystem Security Screen Integrated Devices Screen OptionsExit Screen System and Setup Password FeaturesEnabled DisabledAssigning a System Password Using the System PasswordDeleting or Changing an Existing System Password Using the Setup PasswordSee Disabling a Forgotten Password Baseboard Management Controller ConfigurationEntering the BMC Setup Module BMC Setup Module OptionsChecking the Equipment Safety First-For You and Your SystemTroubleshooting IRQ Assignment Conflicts Start-Up RoutineIRQ Line Assignment Troubleshooting External ConnectionsTroubleshooting the Video Subsystem IRQ Assignment DefaultsTroubleshooting Basic I/O Functions Troubleshooting the KeyboardTroubleshooting the Mouse Troubleshooting a USB Device Troubleshooting a Serial I/O DeviceTroubleshooting a NIC Troubleshooting a Wet SystemClose the system. See Opening and Closing the System Troubleshooting the System Battery Troubleshooting a Damaged SystemTroubleshooting System Cooling Problems Troubleshooting Power SuppliesTroubleshooting a Fan Troubleshooting System MemoryTroubleshooting an SD Card or Internal USB Key Troubleshooting an External Tape Drive Troubleshooting an Optical DriveRemove the bezel. See Removing the Front Bezel Troubleshooting a Hard DriveTroubleshooting a SAS Controller Daughter Card Troubleshooting Expansion Cards Troubleshooting the Microprocessors
Related manuals
Manual 200 pages 56.14 Kb