Dell XFR D630 service manual Revision A01

Page 48

DellTM XFR D630 Fully Rugged Notebook Service Manual

7.Assemble the keyboard onto the palmrest.

a.Apply pressure around the perimeter to ensure the keyboard lip is properly fitted to the palmrest bucket.

b.Apply pressure on the area around the keyboard stiffener bar and near the right hinge to ensure there is no bulging.

Page 48 of 106

Revision A01

Page 47 Page 49
Image 48
Page 47 Page 49
Contents DellTM XFR D630 Fully Rugged NotebookRevision A01 Table of Contents 10.10 24.1 Before You Begin Recommended ToolsTurning Off Your Computer Before Working Inside Your ComputerRevision A01 Screw Chart Screw Image Part Number DescriptionSCR,M3X14,PHH,MSCR,ZPS,XFR CSK Screw M3 X 10 -BLACK SCR,M2.5X5,PHH,TF,BCS PAN Head Screw M2 X 8-BLACK XBay Devices Hard Drive Revision A01 Revision A01 Replacing the Stylus Clip Close Up View of Installed Stylus Clip Handle Replacing the StylusInstalling the Handle Removing the HandlePort Covers Comms DoorRemoving the Comms Door Installing the Comms Door Docking DoorRemoving the Docking Door Revision A01 Installing the Docking Door VGA Door Removing the VGA DoorRevision A01 Installing the VGA Door Power Door Removing the Power DoorInstalling the Power Door XBay Door Removing the XBay DoorInstalling the XBay Door Audio Ports/WiFi Door Removing the Audio Ports/WiFi DoorInstalling the Audio Ports/WiFi Door USB Side DoorInstalling the USB Side Door Removing the USB Side DoorUSB Rear Door Removing USB Rear DoorInstalling USB Rear Door PC Card Slot DoorRemoving the PC Card Slot Door Installing the PC Card Slot Door Hinge Cover Removing the Hinge CoverRevision A01 Installing the Hinge Cover KeyboardsStandard Keyboard Removing the Standard KeyboardRevision A01 Installing the Standard Keyboard Rugged KeyboardRemoving the Rugged Keyboard Revision A01 Revision A01 Installing the Rugged Keyboard KYBD, 87, US, ENG, RGD, XFR Rubber keyboard stiffener bar Revision A01 Connectors should not stack above this level Revision A01 Revision A01 Revision A01 Memory Dimm aMemory module Dimm a Dimm B Screws Memory module cover Display Assembly Removing the Display Assembly Revision A01 Revision A01 Revision A01 Installing the Display Assembly Revision A01 Removing the Display Bezel Installing the Display Bezel Removing the Display PanelRevision A01 Installing the Display Panel Installing the Display Top Cover Removing the Display Top CoverRemoving the Display Latch Internal Card with Bluetooth Wireless Technology Installing the Display LatchRemoving the Bluetooth Wireless Card Installing the Bluetooth Wireless Card WWAN, FCM & SIM Cards Mobile Broadband Network Wwan CardWwan card Antenna cable connectors Metal securing tabs Wwan with Passthu Board & Passthru Cable Flash Cache Module Removing the Flash Cache ModuleInstalling the Flash Cache Module Subscriber Identity Module SIM Card Coin-Cell Battery Removing the Coin-Cell BatteryInstalling the Coin-Cell Battery Palm Rest Removing the Palm RestRevision A01 Installing the Palm Rest Underside of Palm Rest showing Touchpad Cable RouteWireless Local Area Network Wlan Cards Removing the Wlan CardWlan card Antenna cable connectors Metal securing tabs Installing the Wlan Card Modem Removing the ModemProcessor Thermal-Cooling Assembly Installing the ModemRemoving the Processor Thermal-Cooling Assembly Installing the Processor Thermal-Cooling Assembly Processor Removing the ProcessorInstalling the Processor PC Card Reader Removing the PC Card Cage Installing the PC Card Cage SpeakerRemoving the Speaker Installing the Speaker 21 FanRemoving the Fan Installing the Fan System Board Removing the System BoardWlan Revision A01 Installing the System Board Revision A01 Revision A01 Flashing the Bios Flashing the Bios From a CDFlashing the Bios From the Hard Drive RF Passthru Board Removing the RF Passthru BoardInstalling the RF Passthru Board WwanBottom Chassis Removing the Bottom ChassisInstalling the Bottom Chassis Installing the Modem CableRemoving the Modem Cable Revision A01
Top Page Image Contents