Dell XFR D630 service manual Connectors should not stack above this level

Page 47

DellTM XFR D630 Fully Rugged Notebook Service Manual

5.Place connectors from the spliced cable and the backlight power cable in the recessed area of the thermal solution. Stack them and use a 2.5” piece of Kapton tape to hold them in place below the level of the palmrest.

Connectors should not stack above this level.

6.Assemble the keyboard stiffener bar into the slot above the power and audio buttons. Do this before assembling the keyboard to the palmrest.

Page 47 of 106

Revision A01

Image 47
Contents Fully Rugged Notebook DellTM XFR D630Revision A01 Table of Contents 10.10 24.1 Before Working Inside Your Computer Before You BeginRecommended Tools Turning Off Your ComputerRevision A01 Screw Image Part Number Description Screw ChartSCR,M3X14,PHH,MSCR,ZPS,XFR CSK Screw M3 X 10 -BLACK SCR,M2.5X5,PHH,TF,BCS PAN Head Screw M2 X 8-BLACK XBay Devices Hard Drive Revision A01 Revision A01 Replacing the Stylus Clip Close Up View of Installed Stylus Clip Replacing the Stylus HandleRemoving the Handle Installing the HandleRemoving the Comms Door Port CoversComms Door Removing the Docking Door Installing the Comms DoorDocking Door Revision A01 Installing the Docking Door Removing the VGA Door VGA DoorRevision A01 Installing the VGA Door Installing the Power Door Power DoorRemoving the Power Door Removing the XBay Door XBay DoorInstalling the XBay Door Removing the Audio Ports/WiFi Door Audio Ports/WiFi DoorUSB Side Door Installing the Audio Ports/WiFi DoorRemoving the USB Side Door Installing the USB Side DoorRemoving USB Rear Door USB Rear DoorRemoving the PC Card Slot Door Installing USB Rear DoorPC Card Slot Door Installing the PC Card Slot Door Removing the Hinge Cover Hinge CoverRevision A01 Removing the Standard Keyboard Installing the Hinge CoverKeyboards Standard KeyboardRevision A01 Removing the Rugged Keyboard Installing the Standard KeyboardRugged Keyboard Revision A01 Revision A01 Installing the Rugged Keyboard KYBD, 87, US, ENG, RGD, XFR Rubber keyboard stiffener bar Revision A01 Connectors should not stack above this level Revision A01 Revision A01 Revision A01 Dimm a MemoryMemory module Dimm a Dimm B Screws Memory module cover Display Assembly Removing the Display Assembly Revision A01 Revision A01 Revision A01 Installing the Display Assembly Revision A01 Removing the Display Bezel Removing the Display Panel Installing the Display BezelRevision A01 Installing the Display Panel Removing the Display Top Cover Installing the Display Top CoverRemoving the Display Latch Removing the Bluetooth Wireless Card Internal Card with Bluetooth Wireless TechnologyInstalling the Display Latch Installing the Bluetooth Wireless Card Mobile Broadband Network Wwan Card WWAN, FCM & SIM CardsWwan card Antenna cable connectors Metal securing tabs Wwan with Passthu Board & Passthru Cable Removing the Flash Cache Module Flash Cache ModuleInstalling the Flash Cache Module Subscriber Identity Module SIM Card Removing the Coin-Cell Battery Coin-Cell BatteryInstalling the Coin-Cell Battery Removing the Palm Rest Palm RestRevision A01 Underside of Palm Rest showing Touchpad Cable Route Installing the Palm RestRemoving the Wlan Card Wireless Local Area Network Wlan CardsWlan card Antenna cable connectors Metal securing tabs Installing the Wlan Card Removing the Modem ModemInstalling the Modem Processor Thermal-Cooling AssemblyRemoving the Processor Thermal-Cooling Assembly Installing the Processor Thermal-Cooling Assembly Removing the Processor ProcessorInstalling the Processor PC Card Reader Removing the PC Card Cage Removing the Speaker Installing the PC Card CageSpeaker Removing the Fan Installing the Speaker21 Fan Installing the Fan Removing the System Board System BoardWlan Revision A01 Installing the System Board Revision A01 Revision A01 Flashing the Bios From the Hard Drive Flashing the BiosFlashing the Bios From a CD Removing the RF Passthru Board RF Passthru BoardWwan Installing the RF Passthru BoardRemoving the Bottom Chassis Bottom ChassisRemoving the Modem Cable Installing the Bottom ChassisInstalling the Modem Cable Revision A01