Manuals / Black Box / Computer Equipment / Network Router

Black Box COMPACT T1 quick start Chassis Connectors and Buttons, Interface Connectors, Quick Start

Models: COMPACT T1

1 42

Download 42 pages 35.13 Kb

Page 15

Image 15

Quick Start

Chassis Connectors and Buttons

The following illustrations show all connectors on the back of the unit.

AC Power Connector

Alarms

Reset

Ground Terminals

-48V/Battery

Ethernet [10Base-T]

T1-2

Connectors

T1-1

25-Pair Telco Connectors

RS-232 Craft Port

Interface Connectors

The following are the Compact T1 chassis interface connectors:

λT1-1 and T1-2 line connection ports each equipped with standard RJ-48C 8-pin connector jack

λRS-232 craft port connector

λTip and Ring Analog Interfaces equipped with standard 25-pair Telco Connectors

λ10Base-T Ethernet port to be connected to a remote management tool such as Telnet or an SNMP-based Network Management System with an RJ-45 8-pin connector jack

λExternal Alarm Connector

λGround Lugs

Compact T1 - Release 6.1

Page 15

Image 15

Black Box COMPACT T1 quick start Chassis Connectors and Buttons, Interface Connectors, Quick Start

Contents

Compact T1 QUICK START GUIDEMAY PRODUCT P/N MT850A 002-0162-0001 Controller IP Router CMG Router Supporting Software VersionPREFACE Safety InformationPreface Electrostatic Discharge ESD Precautionsν Rack Mounting Optional Feature ν Compliant Installation QUICK STARTν Unpacking and Inspection ν Installation Environment ν Assembly of Compact T1 ν Wall MountingInstallation Environment Unpacking and InspectionQuick Start Quick Start Assembly of Compact T1Quick Start Wall MountingBracket Ear Left Side View Rack Mounting Optional FeatureRack Mounting Optional Feature Quick StartQuick Start Heat Baffle Left Side ViewFront View 5. Slide the Unit into rack mounting bracket Rack Mounting Optional FeatureQuick Start 4. Remove wall mount and screws from UnitCompact T1 Chassis occupies 2 RUs 1 RU free space Quick StartQuick Start Compliant InstallationPower Cables Signal CablesFerrite Beads shipped with Adit chassis Ferrite BeadsService Card Cables that Require Additional Ferrite Beads Quick StartChassis Connectors and Buttons Interface ConnectorsQuick Start Quick Start Chassis Ground ConnectorGround Terminals Compression Screw Lug Barrel Ground Lug48V Battery Power ResetPower Connections AC PowerQuick Start To connect -48 VDC powerQuick Start External Alarm ConnectorL A R M Interface ConnectorsPin Location 25-Pair Telco ConnectorsQuick Start PairInterface Connectors Quick StartCompact T1 - Release RS-232 Craft Port Female DB-9 Quick StartPin Number Quick Start T1 Connection Ports10Base-T Ethernet Interface ConnectorsCommand Line Interface CLI Local and Remote Management OptionQuick Start Quick Start ConfigurationInitial Setup Set Up SecurityQuick Start Set Up a DS1/T1 Set Up a DS0/ChannelQuick Start Quick Start Set Up an Analog PortUse the following commands to set up an analog port ConfigurationQuick Start Set Up the Router IP or CMG CardsConfiguration Set Up a ISDN BRI ServiceEstablish a Static Channel Connection Use the following commands to establish a static channel connectionQuick Start Set Up the OCU-DP CardThe following is a basic setup for the OCU-DP card ConfigurationSet Up a V.35 Port Change the IP Address of the DS0 Management ChannelQuick Start Quick Start Upgrade the Controller SoftwareUpgrade the Router IP or CMG Software Install Country Specific Ringer TonesController Cards Controller CardsT1 Controller Card Quick StartCompact T1 - Release Quick StartLEDs Controller CardsQuick Start Power Supplies115 VAC/-48 VDC Power Supply Power SuppliesService Cards FXO CardQuick Start FXS and FXS5G card FXS CardService Cards Quick StartISDN BRI Card OCU-DP CardQuick Start Quick Start Quad T1 CardV.35/V.54 Card Service CardsCompact T1 - Release CMG Router CardService Cards Quick StartIP Router Card Service CardsQuick Start