Manuals / Black Box / Computer Equipment / Network Router

Black Box COMPACT T1 quick start Chassis Ground Connector, Ground Terminals, Quick Start

Models: COMPACT T1

1 42

Download 42 pages 35.13 Kb

Page 16

Image 16

Quick Start

Interface Connectors

Chassis Ground Connector

Ground Terminals

1.Route wire (#6 or #8 AWG copper) from building ground to lug on Unit.

2.Strip insulation off wire end, if necessary.

Compression

Screw

Lug Barrel

Ground Lug

3.Loosen compression screw until opening is large enough to accept ground wire.

4.Insert ground wire into lug barrel, beneath compression plate and tighten compression screw.

5.Attach ground lug to chassis

12	Compact T1 - Release 6.1

Page 16

Image 16

Black Box COMPACT T1 Chassis Ground Connector, Ground Terminals, Compression Screw Lug Barrel Ground Lug, Quick Start

Contents

QUICK START GUIDE Compact T1MAY PRODUCT P/N MT850A 002-0162-0001 Supporting Software Version Controller IP Router CMG RouterSafety Information PREFACEElectrostatic Discharge ESD Precautions PrefaceQUICK START ν Unpacking and Inspection ν Installation Environmentν Assembly of Compact T1 ν Wall Mounting ν Rack Mounting Optional Feature ν Compliant InstallationUnpacking and Inspection Installation EnvironmentQuick Start Assembly of Compact T1 Quick StartWall Mounting Quick StartRack Mounting Optional Feature Rack Mounting Optional FeatureQuick Start Bracket Ear Left Side ViewHeat Baffle Left Side View Quick StartFront View Rack Mounting Optional Feature Quick Start4. Remove wall mount and screws from Unit 5. Slide the Unit into rack mounting bracketQuick Start Compact T1 Chassis occupies 2 RUs 1 RU free spaceCompliant Installation Power CablesSignal Cables Quick StartFerrite Beads Service Card Cables that Require Additional Ferrite BeadsQuick Start Ferrite Beads shipped with Adit chassisInterface Connectors Chassis Connectors and ButtonsQuick Start Chassis Ground Connector Ground TerminalsCompression Screw Lug Barrel Ground Lug Quick StartPower Reset Power ConnectionsAC Power 48V BatteryTo connect -48 VDC power Quick StartExternal Alarm Connector L A R MInterface Connectors Quick Start25-Pair Telco Connectors Quick StartPair Pin LocationQuick Start Interface ConnectorsCompact T1 - Release Quick Start RS-232 Craft Port Female DB-9Pin Number T1 Connection Ports 10Base-T EthernetInterface Connectors Quick StartLocal and Remote Management Option Command Line Interface CLIQuick Start Configuration Quick StartSet Up Security Initial SetupQuick Start Set Up a DS0/Channel Set Up a DS1/T1Quick Start Set Up an Analog Port Use the following commands to set up an analog portConfiguration Quick StartSet Up the Router IP or CMG Cards Quick StartSet Up a ISDN BRI Service Establish a Static Channel ConnectionUse the following commands to establish a static channel connection ConfigurationSet Up the OCU-DP Card The following is a basic setup for the OCU-DP cardConfiguration Quick StartChange the IP Address of the DS0 Management Channel Set Up a V.35 PortQuick Start Upgrade the Controller Software Upgrade the Router IP or CMG SoftwareInstall Country Specific Ringer Tones Quick StartController Cards T1 Controller CardQuick Start Controller CardsQuick Start LEDsController Cards Compact T1 - ReleasePower Supplies 115 VAC/-48 VDC Power SupplyPower Supplies Quick StartFXO Card Service CardsQuick Start FXS Card Service CardsQuick Start FXS and FXS5G cardOCU-DP Card ISDN BRI CardQuick Start Quad T1 Card V.35/V.54 CardService Cards Quick StartCMG Router Card Service CardsQuick Start Compact T1 - ReleaseService Cards IP Router CardQuick Start