Manuals / Black Box / Computer Equipment / Network Router

Black Box COMPACT T1 quick start Quick Start, Compact T1 Chassis occupies 2 RUs 1 RU free space

Models: COMPACT T1

1 42

Download 42 pages 35.13 Kb

Page 12

Image 12

Quick Start

Rack Mounting (Optional Feature)

As many as 20 Units can be mounted on a single 7 foot rack, as shown in the following illustration (2 Adits are mounted side-by side and 10 high).

Compact T1 Chassis occupies 2 RUs

1 RU free space

Compact T1 Chassis = 2 RUs (3.5 in) Spacing = 1 RU above and below for each unit.

NOTE: the mounting brackets are 7 inches high and will not allow units to be mounted closer than recommended.

8	Compact T1 - Release 6.1

Page 12

Image 12

Black Box COMPACT T1 quick start Quick Start, Compact T1 Chassis occupies 2 RUs 1 RU free space

Contents

Compact T1 QUICK START GUIDEMAY PRODUCT P/N MT850A 002-0162-0001 Supporting Software Version Controller IP Router CMG RouterSafety Information PREFACEElectrostatic Discharge ESD Precautions PrefaceQUICK START ν Unpacking and Inspection ν Installation Environmentν Assembly of Compact T1 ν Wall Mounting ν Rack Mounting Optional Feature ν Compliant InstallationInstallation Environment Unpacking and InspectionQuick Start Assembly of Compact T1 Quick StartWall Mounting Quick StartRack Mounting Optional Feature Rack Mounting Optional FeatureQuick Start Bracket Ear Left Side ViewQuick Start Heat Baffle Left Side ViewFront View Rack Mounting Optional Feature Quick Start4. Remove wall mount and screws from Unit 5. Slide the Unit into rack mounting bracketQuick Start Compact T1 Chassis occupies 2 RUs 1 RU free spaceCompliant Installation Power CablesSignal Cables Quick StartFerrite Beads Service Card Cables that Require Additional Ferrite BeadsQuick Start Ferrite Beads shipped with Adit chassisChassis Connectors and Buttons Interface ConnectorsQuick Start Chassis Ground Connector Ground TerminalsCompression Screw Lug Barrel Ground Lug Quick StartPower Reset Power ConnectionsAC Power 48V BatteryTo connect -48 VDC power Quick StartExternal Alarm Connector L A R MInterface Connectors Quick Start25-Pair Telco Connectors Quick StartPair Pin LocationInterface Connectors Quick StartCompact T1 - Release RS-232 Craft Port Female DB-9 Quick StartPin Number T1 Connection Ports 10Base-T EthernetInterface Connectors Quick StartCommand Line Interface CLI Local and Remote Management OptionQuick Start Configuration Quick StartInitial Setup Set Up SecurityQuick Start Set Up a DS1/T1 Set Up a DS0/ChannelQuick Start Set Up an Analog Port Use the following commands to set up an analog portConfiguration Quick StartSet Up the Router IP or CMG Cards Quick StartSet Up a ISDN BRI Service Establish a Static Channel ConnectionUse the following commands to establish a static channel connection ConfigurationSet Up the OCU-DP Card The following is a basic setup for the OCU-DP cardConfiguration Quick StartSet Up a V.35 Port Change the IP Address of the DS0 Management ChannelQuick Start Upgrade the Controller Software Upgrade the Router IP or CMG SoftwareInstall Country Specific Ringer Tones Quick StartController Cards T1 Controller CardQuick Start Controller CardsQuick Start LEDsController Cards Compact T1 - ReleasePower Supplies 115 VAC/-48 VDC Power SupplyPower Supplies Quick StartService Cards FXO CardQuick Start FXS Card Service CardsQuick Start FXS and FXS5G cardISDN BRI Card OCU-DP CardQuick Start Quad T1 Card V.35/V.54 CardService Cards Quick StartCMG Router Card Service CardsQuick Start Compact T1 - ReleaseIP Router Card Service CardsQuick Start