Datamax PE manual Setting Up the Printer, Connecting the Printer

Page 19

Setting Up the Printer

3.0Introduction

This chapter explains how to connect the printer to the host, load media and print a configuration label.

3.1Connecting the Printer

;Note: Ensure that the printer’s power switch is ‘off’ when connecting the AC power cord or any interface cable.

Connect the AC power cord to the back of the printer before plugging into a properly grounded outlet. The printer can be connected to the host computer with a parallel or serial cable, (see Appendix C). The applicator connections should also be made at this time. The figure below shows the position of the interface ports.

Figure 3-1 Connecting the Printer

PE Series Operator’s Manual

9

Image 19

Contents PE Series Operator’s Manual Page 88-2082-01 Rev. C1 Page Agency Compliance and Approvals Important Safety Instructions Contents Using Your Printer Appendix D Appendix aAppendix B Appendix CPage Introduction Printer OverviewRight-Hand Model About This Printer Standard FeaturesOptional Features PE Series Operator’s Manual Getting Started Before Using This PrinterInspecting the Printer Right-Hand Model, External Front View General OverviewRight-hand Model, Interior Front View Connecting the Printer Setting Up the PrinterHead-Lift Lever Loading MediaMedia Loading Media Loading detail Ribbon Loading Path Loading Ribbon Thermal TransferJ-Hook Removal of a Partially Used Roll of Ribbon Ribbon RemovalRemoval of a Completely Used Ribbon Flash Cartridge Connector Location Installing a Flash Cartridge10 Inserting the Memory Cartridge Printing a Configuration Label 11 Configuration Label PE Series Operator’s Manual Configuration Label Explanation 12 Test Pattern Label Test Pattern LabelPin # Function Direction Applicator ConnectionApplicator Port Pin Assignments Pin function explanation Pin 4 Not Used13 End Print Signal Options Description Options PortOptions Port Pin Assignments PE Series Operator’s Manual Using the Printer’s Front Panel Using Your PrinterControl Buttons Menu Keypad LightsLCD Contrast Basic Functions Accessing the Menu TreeFactory preset Value range PE Output Signal Advanced SetupBackfeed Cntrl Heat SettingRibbon Low Label Width Print SpeedSlew Speed Backfeed SpeedSecurity Check Factory SettingsModify Password Symbol SetOffset Bias *220 ProdigyPlus ModePause Mode Feedback ModeComm Setup *PORTA *9600 *8 *N *1 *BOTH Control Codes Test ModeSerial Loopback Test PrintFront Panel Test I/OCopy Module Installed OptionsPrint Directory Print FileInputs Sensor Name Possible Condition Sensor DefinitionsPE Series Operator’s Manual Media Sensor Adjustment Example of the Media Width Adjustment Media Width AdjustmentLabel Presentation Label Start of PrintSetting Start of Print and Peel Position Controlling Print Quality PE Series Operator’s Manual Exterior InteriorPrinter Cleaning Schedule Cleaning ScheduleArea Method Interval Cleaning the Printhead Cleaning the PrintheadCleaning the Platen Roller Printer fails to power up no lights Troubleshooting TipsSkips Labels every other Black boxes in displayPoor Print Quality No PrintMissing Data in the printed label Alarm Description Error MessagesLCD Display BQQMJDBUPS!CVTZ DPWFS!PQFO!GBVM U IFBE!VQ!GBVMU PVU!PG!TUPDL QSJOUIFBE!GMU SJCCPO!GBVMU SJC!TBWFS!GBVMU UPG!GBVMU Ascii Character Dump Label Character Dump ModePage Appendix a Ascii Control ChartPE Series Operator’s Manual Available Fonts and Barcodes Appendix BFont Matrix Sizes Charac. Per Inch Dot 203 Height Width Human-Readable FontsTable B-1 Human-Readable Font Sizes Table B-2 Valid Human-Readable Font Ascii CharactersPage Identifies the internal Triumvirate font Table B-3 Valid Bar Code Font Ascii Characters Barcode FontsPE Series Operator’s Manual Barcode O Barcode S Barcode T Barcode z Cable Listing Appendix CTable C-1 Serial Cable Requirements PE Series Operator’s Manual Applicator Port Test Box Appendix DPE Series Operator’s Manual Appendix E Error CodesPE Series Operator’s Manual Communications Printer SpecificationsAppendix F PrintingMedia ElectricalEnvironmental PhysicalFonts and Bar Codes Figure F-1 Print Engine Critical Dimensions Printer DimensionsTable F-1 Acceptable Media Specifications Media SpecificationsTable F-2 Media and Ribbon Overview Media and Ribbon BasicsLabel Type Print Image Ribbon Type Speed Energy Durability Menu Tree Appendix GPE Series Operator’s Manual Thermal printhead Warranty InformationAppendix H PrinterGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability PE Series Operator’s Manual