Datamax PE manual Accessing the Menu Tree, Basic Functions

Page 40

4.1Accessing the Menu Tree

The menu is divided between basic function and advanced setup levels. (To see a complete overview, the Menu Tree is located in Appendix G.)

;Note: Default values or settings may vary depending on the version and customer applications. Factory default settings will be indicated with * symbol.

4.1.1 Basic Functions

There are nine basic functions including a gateway to the advanced setup level.

Print Method	Column Adjust
Sensor Top of Form	PE Applicator HW
Darkness	Advanced Setup
Start of Print

LCD :

UVF!!GFC14!!22;66B

!!!

SFBEZ

From the Printer Ready screen, enter the Basic Function screen by pressing the Ø key :

Qsjou!Nfuipe

Direct *Transfer

Tfmfdu!UPG

*Gap Reflective Continuous

Controls the type of print method to be used.

Enables direct-thermal printing (no ribbon). Enables thermal-transfer printing (ribbon installed).

Controls the type of media sensing to be used.

Senses on a gap or notch between each label. Senses on a reflective mark between each label. Senses only presence, TOF set by label format.

30	PE Series Operator’s Manual

Image 40

Contents PE Series Operator’s Manual Page 88-2082-01 Rev. C1 Page Agency Compliance and Approvals Important Safety Instructions Contents Using Your Printer Appendix a Appendix BAppendix C Appendix DPage Introduction Printer OverviewRight-Hand Model Standard Features About This PrinterOptional Features PE Series Operator’s Manual Before Using This Printer Getting StartedInspecting the Printer General Overview Right-Hand Model, External Front ViewRight-hand Model, Interior Front View Setting Up the Printer Connecting the PrinterLoading Media Head-Lift LeverMedia Loading Media Loading detail Loading Ribbon Thermal Transfer Ribbon Loading PathJ-Hook Ribbon Removal Removal of a Partially Used Roll of RibbonRemoval of a Completely Used Ribbon Installing a Flash Cartridge Flash Cartridge Connector Location10 Inserting the Memory Cartridge Printing a Configuration Label 11 Configuration Label PE Series Operator’s Manual Configuration Label Explanation Test Pattern Label 12 Test Pattern LabelApplicator Connection Applicator Port Pin Assignments Pin function explanationPin 4 Not Used Pin # Function Direction13 End Print Signal Options Description Options PortOptions Port Pin Assignments PE Series Operator’s Manual Using the Printer’s Front Panel Using Your PrinterControl Buttons Menu Keypad LightsLCD Contrast Accessing the Menu Tree Basic FunctionsFactory preset Value range Advanced Setup PE Output SignalBackfeed Cntrl Heat SettingRibbon Low Print Speed Slew SpeedBackfeed Speed Label WidthFactory Settings Modify PasswordSymbol Set Security CheckProdigyPlus Mode Pause ModeFeedback Mode Offset Bias *220Test Mode Comm Setup *PORTA *9600 *8 *N *1 *BOTH Control CodesTest Print Front PanelTest I/O Serial LoopbackInstalled Options Print DirectoryPrint File Copy ModuleSensor Definitions Inputs Sensor Name Possible ConditionPE Series Operator’s Manual Media Sensor Adjustment Media Width Adjustment Example of the Media Width AdjustmentLabel Start of Print Label PresentationSetting Start of Print and Peel Position Controlling Print Quality PE Series Operator’s Manual Interior ExteriorPrinter Cleaning Schedule Cleaning ScheduleArea Method Interval Cleaning the Printhead Cleaning the PrintheadCleaning the Platen Roller Troubleshooting Tips Printer fails to power up no lightsBlack boxes in display Skips Labels every otherNo Print Poor Print QualityMissing Data in the printed label Alarm Description Error MessagesLCD Display BQQMJDBUPS!CVTZ DPWFS!PQFO!GBVM U IFBE!VQ!GBVMU PVU!PG!TUPDL QSJOUIFBE!GMU SJCCPO!GBVMU SJC!TBWFS!GBVMU UPG!GBVMU Character Dump Mode Ascii Character Dump LabelPage Ascii Control Chart Appendix aPE Series Operator’s Manual Appendix B Available Fonts and BarcodesHuman-Readable Fonts Table B-1 Human-Readable Font SizesTable B-2 Valid Human-Readable Font Ascii Characters Font Matrix Sizes Charac. Per Inch Dot 203 Height WidthPage Identifies the internal Triumvirate font Barcode Fonts Table B-3 Valid Bar Code Font Ascii CharactersPE Series Operator’s Manual Barcode O Barcode S Barcode T Barcode z Cable Listing Appendix CTable C-1 Serial Cable Requirements PE Series Operator’s Manual Appendix D Applicator Port Test BoxPE Series Operator’s Manual Error Codes Appendix EPE Series Operator’s Manual Printer Specifications Appendix FPrinting CommunicationsElectrical EnvironmentalPhysical MediaFonts and Bar Codes Printer Dimensions Figure F-1 Print Engine Critical DimensionsMedia Specifications Table F-1 Acceptable Media SpecificationsTable F-2 Media and Ribbon Overview Media and Ribbon BasicsLabel Type Print Image Ribbon Type Speed Energy Durability Appendix G Menu TreePE Series Operator’s Manual Warranty Information Appendix HPrinter Thermal printheadWarranty Service Procedures General Warranty ProvisionsLimitation of Liability PE Series Operator’s Manual