Datamax PE manual Installed Options, Print Directory, Print File, Copy Module, Format Module

Page 49

Nbjoufobodf

(cont.)

Installed Options

Cutter

Ribbon Saver

Npevmft

Print Directory

Module A

Module B

Print File

Print File on

Module A

Print File on

Module B

Copy Module

Copy From

Module A

Copy From

Module B

Format Module

Format Module A

Format Module B

Test Module

Test Module A

Test Module B

There are two installed options to choose from:

Modules contain a set of five memory function routines. Some of these memory tests are destructive, in this case, the printer will prompt “Are you sure?” before beginning.

Prints a list of all files (fonts, images and labels), stored on the selected module.

Module A is the printer's internal memory allocation. Module B refers to an external Flash, if equipped.

Prints a file from a selected module.

Prints from Module A; specify file type and then file name. The printer will then print the contents. Same function as Module A, but prints the specified contents of the external module file.

Copies data from one module to another. Copies from Module A to Module B.

Copies from Module B to Module A.

Formats a selected memory module.

Caution! Formatting permanently erases data!

Formats Module A. Printer will prompt, “Are You Sure?” All data will be lost.

Same as Module A. The Write Protect Switch must be turned ‘Off’ to format this module.

Tests the selected memory module by writing to, reading from and then verifying the data for accuracy.

Caution! Testing permanently erases data!

Tests Module A. The printer will prompt, “Are You Sure?” All data will be lost.

Same as Module A. The Write Protect Switch must be turned ‘Off’ to test this module.

PE Series Operator’s Manual

39

Image 49

Contents PE Series Operator’s Manual Page 88-2082-01 Rev. C1 Page Agency Compliance and Approvals Important Safety Instructions Contents Using Your Printer Appendix B Appendix aAppendix C Appendix DPage Introduction Printer OverviewRight-Hand Model About This Printer Standard FeaturesOptional Features PE Series Operator’s Manual Getting Started Before Using This PrinterInspecting the Printer Right-Hand Model, External Front View General OverviewRight-hand Model, Interior Front View Connecting the Printer Setting Up the PrinterHead-Lift Lever Loading MediaMedia Loading Media Loading detail Ribbon Loading Path Loading Ribbon Thermal TransferJ-Hook Removal of a Partially Used Roll of Ribbon Ribbon RemovalRemoval of a Completely Used Ribbon Flash Cartridge Connector Location Installing a Flash Cartridge10 Inserting the Memory Cartridge Printing a Configuration Label 11 Configuration Label PE Series Operator’s Manual Configuration Label Explanation 12 Test Pattern Label Test Pattern LabelApplicator Port Pin Assignments Pin function explanation Applicator ConnectionPin 4 Not Used Pin # Function Direction13 End Print Signal Options Description Options PortOptions Port Pin Assignments PE Series Operator’s Manual Using the Printer’s Front Panel Using Your PrinterControl Buttons Menu Keypad LightsLCD Contrast Basic Functions Accessing the Menu TreeFactory preset Value range PE Output Signal Advanced SetupBackfeed Cntrl Heat SettingRibbon Low Slew Speed Print SpeedBackfeed Speed Label WidthModify Password Factory SettingsSymbol Set Security Check Pause Mode ProdigyPlus Mode Feedback Mode Offset Bias *220Comm Setup *PORTA *9600 *8 *N *1 *BOTH Control Codes Test ModeFront Panel Test PrintTest I/O Serial LoopbackPrint Directory Installed OptionsPrint File Copy ModuleInputs Sensor Name Possible Condition Sensor DefinitionsPE Series Operator’s Manual Media Sensor Adjustment Example of the Media Width Adjustment Media Width AdjustmentLabel Presentation Label Start of PrintSetting Start of Print and Peel Position Controlling Print Quality PE Series Operator’s Manual Exterior InteriorPrinter Cleaning Schedule Cleaning ScheduleArea Method Interval Cleaning the Printhead Cleaning the PrintheadCleaning the Platen Roller Printer fails to power up no lights Troubleshooting TipsSkips Labels every other Black boxes in displayPoor Print Quality No PrintMissing Data in the printed label Alarm Description Error MessagesLCD Display BQQMJDBUPS!CVTZ DPWFS!PQFO!GBVM U IFBE!VQ!GBVMU PVU!PG!TUPDL QSJOUIFBE!GMU SJCCPO!GBVMU SJC!TBWFS!GBVMU UPG!GBVMU Ascii Character Dump Label Character Dump ModePage Appendix a Ascii Control ChartPE Series Operator’s Manual Available Fonts and Barcodes Appendix BTable B-1 Human-Readable Font Sizes Human-Readable FontsTable B-2 Valid Human-Readable Font Ascii Characters Font Matrix Sizes Charac. Per Inch Dot 203 Height WidthPage Identifies the internal Triumvirate font Table B-3 Valid Bar Code Font Ascii Characters Barcode FontsPE Series Operator’s Manual Barcode O Barcode S Barcode T Barcode z Cable Listing Appendix CTable C-1 Serial Cable Requirements PE Series Operator’s Manual Applicator Port Test Box Appendix DPE Series Operator’s Manual Appendix E Error CodesPE Series Operator’s Manual Appendix F Printer SpecificationsPrinting CommunicationsEnvironmental ElectricalPhysical MediaFonts and Bar Codes Figure F-1 Print Engine Critical Dimensions Printer DimensionsTable F-1 Acceptable Media Specifications Media SpecificationsTable F-2 Media and Ribbon Overview Media and Ribbon BasicsLabel Type Print Image Ribbon Type Speed Energy Durability Menu Tree Appendix GPE Series Operator’s Manual Appendix H Warranty InformationPrinter Thermal printheadGeneral Warranty Provisions Warranty Service ProceduresLimitation of Liability PE Series Operator’s Manual